shelolab SRI21D Скачать руководство пользователя страница 63

Страница: 63 / 70

63 |

P a g e

USER MAINTENANCE

Note:

Does the car actually have gas in the tank? Have you physically verified the computer is

plugged in? Yes, we are going ask some very basic questions. Please bear with us.

Methodical verifications and the elimination of assumptions are often the quickest means of

getting a unit back into operation.

Before Starting

The unit must be connected to a power source that meets the requirements in the Installation chapter

(page 15) and turned on.

A reference temperature device sensor probe must be placed in the chamber.

•

See the probe placement instructions in the

Temperature Calibration procedure

page 46.

The unit must have adequate time to come up to temperature and stabilize.

Failure to wait will result

in an inaccurate diagnosis

•

Allow 4 hours for the unit to achieve its temperature.

•

Start the “Diagnostic Data Procedure”

when the allotted time has passed

, even if the unit fails to

achieve the set point temperature.

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды