manualshive.com logo in svg

shelolab SRI21D, Руководство по установке и эксплуатации

Поделиться
Скачать
shelolab SRI21D Скачать руководство пользователя страница 4

 

4 | 

P a g e  

TABLE OF CONTENTS 

INTRODUCTION ........................................................................................................................................................ 5

 

Read this Manual .................................................................................................................................................................... 5

 

Safety Considerations and Requirements ...................................................................................................................... 5

 

Contacting Assistance .......................................................................................................................................................... 6

 

Engineering Improvements.................................................................................................................................................. 6

 

Temperature Reference Sensor Device .......................................................................................................................... 7

 

RECEIVING YOUR UNIT ........................................................................................................................................... 9

 

Inspect the Shipment ............................................................................................................................................................. 9

 

Orientation Photo ................................................................................................................................................................. 10

 

Recording Data Plate Information .................................................................................................................................... 11

 

INSTALLATION ......................................................................................................................................................... 13

 

Installation Checklist ........................................................................................................................................................... 13

 

Required Ambient Conditions ........................................................................................................................................... 14

 

Environmental Disruption Sources .................................................................................................................................. 14

 

Power Source Requirements ............................................................................................................................................ 15

 

Lifting and Handling ............................................................................................................................................................ 15

 

Install the Chamber in Location ....................................................................................................................................... 16

 

Leveling ................................................................................................................................................................................... 16

 

Attach the Chamber Door Handle .................................................................................................................................. 16

 

Adjust Shelves ........................................................................................................................................................................ 17

 

Deionized and Distilled Water .......................................................................................................................................... 18

 

Installation Cleaning and Disinfection ........................................................................................................................... 18

 

GRAPHIC SYMBOLS ................................................................................................................................................ 19

 

CONTROL PANEL OVERVIEW ............................................................................................................................... 21

 

OPERATION.............................................................................................................................................................. 23

 

Theory of Operation ........................................................................................................................................................... 23

 

Put the Chamber into Operation ..................................................................................................................................... 25

 

Set the Manual Day Mode Temperature Set Point ................................................................................................... 26

 

Set the Manual Night Mode Temperature Set Point ................................................................................................. 29

 

Program Clock Times and Cycle Temperature Set Points ...................................................................................... 32

 

Load the Chamber .............................................................................................................................................................. 38

 

Condensation and the Dew Point .................................................................................................................................. 38

 

Launching the Day - Night Cycle .................................................................................................................................... 39

 

Accessory Compatibility and Power Outlet ................................................................................................................. 39

 

Set the Over Temperature Limit ...................................................................................................................................... 40

 

USER MAINTENANCE .............................................................................................................................................. 41

 

Cleaning and Disinfecting .................................................................................................................................................. 41

 

Minimizing Contamination Exposure ............................................................................................................................. 42

 

Electrical Components ....................................................................................................................................................... 42

 

Refrigeration and Defrosting............................................................................................................................................ 43

 

Diagnostics - Temperature Issues .................................................................................................................................. 59

 

UNIT SPECIFICATIONS .......................................................................................................................................... 67

 

Weight ......................................................................................................................................................................................67

 

Dimensions .............................................................................................................................................................................67

 

Capacity ..................................................................................................................................................................................67

 

Max Shelves For Unit ......................................................................................................................................................... 68

 

Shelf Capacity by Weight .................................................................................................................................................. 68

 

Temperature ......................................................................................................................................................................... 68

 

Power ...................................................................................................................................................................................... 68

 

PARTS AND CONSUMABLES ................................................................................................................................ 69

 

Содержание SRI21D







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды