shelolab SRI21D Скачать руководство пользователя страница 45

Страница: 45 / 70

45 |

P a g e

USER MAINTENANCE

Turning Off the Automatic Defrost

Deactivating the defrost thermostat will result in ice accumulation and a gradual

loss of cooling efficiency. Incubators used for BOD and other closed-container

applications with the defrost thermostat turned off will likely require manual

defrosting every 6 months. Units with open sources of water evaporation and

the defrost thermostat shut off will require manual defrosting every 2 to 3

months. The exact interval depends on the environmental humidity,

temperature setting, and the amount of evaporation taking place inside the

incubation chamber.

Manual Defrosting

Carryout the following steps to manually defrost the unit:

Unplug the incubator, open the chamber door, and allow the unit to stand undisturbed with

the door open for 24 hours.

Wipe up any condensate that forms in the chamber as well as any water around the

incubator after 24 hours have elapsed.

Close the chamber door, plug the incubator power cord into the wall power source, and

place the unit back into operation.

The Low Set Limit Dial (Avoiding Freezing Temps)

The chamber comes with a low set limit system control, set at the factory to turn

off the refrigeration compressor when the incubator air temperature falls to just

above 0°C. This is intended to prevent the incubator from reaching or falling

below the freezing point. Freezing and sub-freezing temperatures risk

damaging plant samples and as well as fluid-filled BOD sample containers.

Under most circumstances, the low set limit system should not be

adjusted. If you wish to adjust the limit setting, please contact

Technical

Support

(page 6).

The manufacturing defect warranty does not cover

damage

to the unit or samples by freezing or subfreezing temperatures if

the low set limit has been set to 0°C or lower than 0°C.

The unit is not

intended to be operated at freezing or sub-freezing temperatures.

Figure 13: Defrost Cycle

Switch – Top Left of Unit,

Back side

Figure 14: Low Set Limit

Dial (Bottom Left of Unit,

Back)

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды