shelolab SRI21D Скачать руководство пользователя страница 34

Страница: 34 / 70

34 |

P a g e

OPERATION

Procedure continued on next page

Programming the day phase parameters

Save the day phase start hour and scroll to the day phase start minute

page.

Press the

Advance button

once to save the hour setting

and

advance to the minute page.

•

“Mi2” is the day phase start minute.

Initial Day Phase Start Minute

Set the day phase start minute.

Use the

and

Down Arrow

keys adjust the day minute (30

minutes in this example).

Adjusted Day Phase Start

Minute

Save the day start minute setting and scroll to the day phase temperature

set point.

Press the

Advance button

once to save the minute setting

and advance to the day temperature set point page.

•

“t.SP3” indicates that this is a temperature set point page

reserved for the day.

Initial Day Phase Temp. Set

Point

10.

Set the day phase temperature set point.

Use the

Arrow keys

to adjust to the day set point.

Adjusted Day Phase Temp.

Set Point

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды