shelolab SRI21D Скачать руководство пользователя страница 56

Страница: 56 / 70

56 |

P a g e

USER MAINTENANCE

Procedure continued on next page

Saving the Night Calibration (Continued)

13.

Navigate to the Settings Menu page (SEt).

Push and hold

both

the Up and Down Arrow Button

simultaneously for 10 seconds.

•

The display will advance to the Operations page after

approximately 5 seconds, then to the Settings Menu page

after another five seconds.

Settings Menu Page

14.

Advance to the Global Settings parameter list.

Press the Up arrow button 3 times.

Global Settings List

15.

Scroll to the Memory parameter.

Press the

green Advance button

15 times.

Temperature Slot

Parameters

16.

Select the night temperature calibration “Set 1” memory slot.

Press the

Up Arrow

button

1 time.

Note:

Select the None memory slot if you do not wish to save the current

calibration value.

Night Cal. Memory Slot

x15

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды