shelolab SRI21D Скачать руководство пользователя страница 53

Страница: 53 / 70

53 |

P a g e

USER MAINTENANCE

Procedure continued on next page

Night Temperature Calibration (Continued)

A display calibration offset must be entered to match the

current display value to the reference device reading.

Reference Device



Determine the offset value and record it for use in three steps.

•

The offset value is the difference between the reference

device reading and the reading of the chamber controller

temperature display.

•

The offset value will be used to adjust the controller

reading to match the reference device.

Reference Sensor

Reading

Controller

Display

Offset

Value

20.0°C

19.0°C

1.0

18.0°C

19.0°C

-1.0

Reference Device

Chamber Display



Matching Offset Value: 1.0

Navigate to the Operations menu page.

Push and hold

both

the Up and Down Arrow

buttons simultaneously for approximately 5

seconds until the oPEr menu appears.

Note:

Holding down both arrows for 10 seconds will open a Set menu

for setting memory parameters. If this happens, press the Reset button

to return to the Home page, then press both Arrow buttons again for 5

seconds.

Operations Menu

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды