shelolab SRI21D Скачать руководство пользователя страница 61

Страница: 61 / 70

61 |

P a g e

USER MAINTENANCE

Unit Performance Specifications

What is the unit designed to do?

Find and note the following unit designation and performance information in the user manual.

Unit Specification

Data Location

Record Data Here

Model Type:

The unit data plate lists the model

type. Verify you are attempting to

diagnose an SRI21D.

What is the operating

temperature range of the unit?

The Temperature block in the Unit

Specifications chapter, page 68.

What is the required ambient

temperature range for the unit?

See below (under this table).

What is the minimum time

required for your unit to come up

to temperature and stabilize?

Allow a minimum of 4 hours of

continual operation for the unit to

achieve a stable temperature.

Standard ambient environment temperature requirements:

•

A room temperature of 15°C - 30°C (59°F - 86°F)

Standard Ventilation Spacing Requirements

•

A minimum of

4 inches (100 mm)

clearance between the sides of the cultivation chamber and any

walls or partitions. A minimum of

25 inches (50 mm)

between the top of the unit and overhead

cover.

This page may be copied for institutional use

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды