shelolab SRI21D Скачать руководство пользователя страница 65

Страница: 65 / 70

65 |

P a g e

USER MAINTENANCE

mbient?

What is the room temperature?

•

For best results, measure the temperature in the same section of the room where the unit is

located. Do not place your thermometer on the unit.

ilot Lights?

1) Is the heating active indicator on the control panel flashing or otherwise illuminating.

During normal operations, the “1” indicator should flicker on and off frequently as the heating

element competes with the refrigeration compressor to achieve a stable temperature within ±0.5°C.

The compressor should run continually when the unit is on.

Refrigeration

: Please listen to hear if the refrigeration compressor is running or not. Note the

absence of compressor noises on the SDRAP form. The operation of the compressor in a noisy

environment can also be detected from feeling for vibrations on the lower back of the unit.

Cooling issues can also be generated by a failure of the blower fan in the cultivation chamber.

Is the Over Temperature Limit Activated indicator illuminating? Answer yes if the light is on

continually or if it is pulsing.

“1” indicates the

controller is calling for

power to the element(s)

Figure 19: Heating Indicator

OVER TEMPERATURE ACTIVATED

Room Air Temperature

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды