shelolab SRI21D Скачать руководство пользователя страница 31

Страница: 31 / 70

31 |

P a g e

OPERATION

Figure 8: Summary quick chart for placing the unit in manual night mode

End of procedure

Put the unit in manual night mode (continued)

Launch the manual night mode and return the display to the

homepage.

Press the

Reset key twice

to save the Event 2

parameter as Off, launch the night mode, and return

to the home page.

Home Page: Night Mode

Active Indicator 6

Set the manual night mode temperature set point

On the homepage, adjust the temperature set point with the unit

operating in the manual night mode.

Use the Up or Down Arrows to adjust the green set

point to that of your cultivation application night

temperature.

•

After the set point is adjusted there may be a pause

as the unit controller calculates the optimum profile

before cooling or heating to the new set point.

Note:

The manual mode temperature set points use memory slots

separate from those of the day - night auto cycle. Changing the manual

temperature set points

will not change

the auto cycle set points.

Manual night mode

temperature set point

adjusted. Cooling to the new

set point.

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды