shelolab SRI21D Скачать руководство пользователя страница 52

Страница: 52 / 70

52 |

P a g e

USER MAINTENANCE

Procedure continued on next page

Saving the Day Calibration (Continued)

15.

Save the current calibration value in the memory slot and return to the

home page by pressing the Reset Button (∞) twice.

•

The first Reset Button press saves the current calibration value in

the presently selected memory slot (Set 2).

•

The second button press scrolls the display back to the Home

page.

Home Page

Night Temperature Calibration

Place the unit in the manual night mode. Please see the

Setting Manual

Night Mode Temperature Procedure

, and use steps 1 – 8 starting on

page 29.

Home Page: Night Mode

Active, 6

Once the unit is in night manual mode, allow the chamber to operate for

2 hours undisturbed, with the door closed. This allows the unit to

achieve temperature stability after the day illumination bulbs in the

chamber turn off.

•

The reference device should register no temperature fluctuations

of greater than ±0.5°C for at least

1 hour

prior to continuing.

•

Failure to wait for stabilization will result in an inaccurate display

reading for the night temperature.

Wait 2 Hours

Once the temperature has stabilized at the manual Night set point,

compare the reference device temperature reading and the reading of

the chamber controller.

If the readings are the same, or a difference between the two falls

within the acceptable range of your protocol, the chamber is

calibrated for temperature.

The temperature calibration

procedure is now complete.

Return the chamber to normal

operations.

- OR -

If a difference falls outside your protocol range, advance to the

next step.

Reference Device

Chamber Display



Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды