shelolab SRI21D Скачать руководство пользователя страница 55

Страница: 55 / 70

55 |

P a g e

USER MAINTENANCE

Procedure continued on next page

Night Temperature Calibration (Continued)

11.

Compare the reference device reading with the chamber

temperature display again.

If the reference device and the chamber temperature display

readings are the same or the difference falls within the range of

your protocol,

advance to Saving the Night Calibration on

page 56

- Or -

If the readings fail to match or fall outside your protocol range,

advance to the next step.

Reference Device



12.

Repeat steps 3 – 11 up to two more times for the night phase if the

unit is still not calibrated.

•

Three calibration attempts may be required to successfully

calibrate units that are more than ±2°C out of calibration.

•

If the readings of the current temperature display and the

reference device are still not close enough to be acceptable by

your laboratory protocol after three calibration attempts,

contact your distributor or technical support for assistance.

Reference Device



Saving the Night Calibration

Once the display reading matches the reference device, the current offset

must be saved in the night temperature calibration memory slot or it will be

lost the next time the chamber is turned off.

Содержание SRI21D







































































Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды

shelolab SRI21D, Руководство по установке и эксплуатации

Результаты поиска

Содержание SRI21D

Отзывы:

Бренды по названию

Популярные бренды