Ricoh AFICIO AP306 Скачать руководство пользователя страница 367

Страница: 367 / 382

Draft 2000/06/22

Message List

Message List

This is a list of messages written to the printer's system log. The system log can
be viewed using the syslog command.

System Log Information

You can use the following methods to view the system log.
• telnet : Use the syslog command.

⇒

P.82

“System log information”

Message when the Network Interface Board starts or restarts

Network Interface Board Ver.x.x.x

The version number of the Network Inter-
face Board.

PRINTER SYSTEM “system name”
Ver.x.x.x

The system name and version of the print-
er.

Attach FileServer=“file server name”

The printer is attached to “file server
name” as the nearest server.

Current Interface Speed:xxxMbps

The speed of the network (10 Mbps or 100
Mbps).

Current IPX address

The current IPX address.

Frametype=“frame type name”

The "frame type name" is configured to be
used on NetWare.

NetBEUI Computer Name=“computer
name”

The NetBEUI Computer Name is defined
as "computer name".

Start httpd

The Web server has been started.

Start npmpd for IPX

The npmpd for IPX protocol has been
started.

Start npmpd for TCP/IP

The npmpd for TCP/IP protocol has been
started.

Start smbd direct print mode(NetBEUI)

You can print from a client on the Win-
dows network via the print server.

Start snmpd Ver.2.0

The SNMP agent of the displayed version
has been started.

Vendor= , Country= , Lang=

The vendor, the country code, and the lan-
guage.

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды