Ricoh AFICIO AP306 Скачать руководство пользователя страница 356

Страница: 356 / 382

Draft 2000/06/22

Appendix

Note

❒

More information about any print job is displayed when the ID number is
added after the prnlog command.

Reference

For more information about the meaning of the data returned with these com-
mands, see P.90

“Configuring the Network Interface Board”

Network Interface Board configuration settings information

Use the show command to display the Network Interface Board configuration
settings.

msh> show [-p]

Note

❒

Add “-p” to the show command to have the information displayed one screen
at a time.

Reference

For more information about the meaning of the data returned with this com-
mand, see P.90

“Configuring the Network Interface Board”

System log information

Use the syslog command to display information stored in the printer's system
log.

msh> syslog

Reference

For more information about the displayed information, see P.93

“System Log

Information”

SNMP

Use the snmp command to display and edit SNMP configuration settings such
as the community name.

Note

❒

You can configure from ten SNMP access settings numbered 1–10.

❒

Default access settings 1 and 2 are as follows.

Number

Community name

public

admin

IP address

0.0.0.0

Access type

read-only

trap off

read-write

trap off

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды