Ricoh AFICIO AP306 Скачать руководство пользователя страница 133

Страница: 133 / 382

Draft 2000/06/22

Error & Status Messages

Printer configuration

You can check the printer's current status using the following method.

❖

telnet

Use the info command.

Note

❒

“*” (asterisk) indicates the current setting.

❒

Items marked by “*” are explained in the following tables.

❖

*1 Input Tray: Name

Item

Description

Input Tray

No.

Name

PageSize

Status List

ID number of the paper tray

Name of the paper tray

Paper size loaded in the paper tray

Current status of the paper tray

Output Tray

No.

Name

Status

ID number of the output tray

Name of the output tray (Fixed to “Standard”)

Current status of the output tray (Fixed to “Normal”)

Emulation

No.

Name

Version

ID number of the emulation used by the printer

Name of the emulation used in the printer

Version of the emulation

Program

No.

Name

ID number of the program

Name of the program (Fixed to blank.)

Name

Description

Tray1

Standard Tray

Tray2

Paper Feed Unit (upper)

Tray3

Paper Feed Unit (lower)

Bypass Tray

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды