Ricoh AFICIO AP306 Скачать руководство пользователя страница 318

Страница: 318 / 382

Draft 2000/06/22

Windows NT 4.0 Configuration

Configuring LPR Port Printing

This section explains the procedure for printing to a LPR port from Windows
NT.

Note

❒

The following procedure assumes that the printer drivers have already been
installed. This is the procedure to change the printer port to LPR.

❒

The TCP/IP protocols must be installed and configured correctly. For more
information about configuring the protocol, see P.32

“Configuring TCP/IP and

IPP for Printing”

Click

[Start]

, point to

[Settings]

, and then click

[Printers]

Click the icon of the printer you want to use. On the

[File]

menu, click

[Prop-

erties]

Click the

[Ports]

tab, and then click

[Add Port]

In the

[Available Printer Ports]

box, click “LPR Port”, and then click

[New Port]

Note

❒

If “LPR Port” does not appear, “Microsoft TCP/IP Printing” has not been
installed.

Type the IP address of the Network Interface Board into the

[Name or address

of server providing lpd]

box.

Type “lp” into the

[Name of printer or print queue on that server]

box, and click

[OK]

Click

[Close]

Confirm that the port name is displayed in the

[Print to the following port(s)]

box and the check mark is inside the check box, and then click

[OK]

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды