Ricoh AFICIO AP306 Скачать руководство пользователя страница 304

Страница: 304 / 382

Draft 2000/06/22

Windows 2000 Configuration

Note

❒

If the printer driver is not installed in the print server, a message appears.
If a driver has been installed on the client, click

[OK]

, and follow the in-

structions on the screen.

❒

There is a Windows 2000 printer driver on the CD-ROM that comes with
the printer.

Select whether to use this printer as the default printer, and click

[Next >]

After installation is complete, click

[Finish]

The icon of the newly installed printer appears in the

[Printers]

window.

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды