Ricoh AFICIO AP306 Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 382

background image

Draft 2000/06/22

Using the Operation Panel

102

5

Interpreting Configuration Page/RICOH-SCRIPT2

❖

Reference

Shows the printer system version and so on. You can also see the status of the
paper tray.

❖

Tray Status

Shows the status of the paper trays.
If you install the paper feed unit, it is described as “Tray2” and/or “Tray3”.
If "FRE" is indicated for bypass tray, it means "Custom Size" is set for bypass
tray.

❖

RPS2 Status

Shows the current settings for the RPS2 mode.

❖

Memory Status

Shows the amount of printer memory, VM area and so on.

Reference

For more information about printer memory and VM area, see the “Oper-
ating Instructions” for RICOH-SCRIPT2 included as a PDF file on the CD-
ROM.

❖

Font Status

This is not used for this printer.

❖

Installed Fonts

Shows the fonts installed on the printer.

❖

Interface Status

Shows that the Network Interface Board is installed.

❖

Network & TCP/IP Status

Shows the network and TCP/IP items and their settings.

❖

Netware Status

Shows the NetWare items and their settings.

❖

NetBEUI Status

Shows the NetBEUI items and their settings.

❖

AppleTalk Status

Shows the AppleTalk items and their settings.

«
...
186
187
188
189
190
...
»

Содержание AFICIO AP306































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFICIO AP306

Бренд: 3D Systems Страницы: 17

Бренд: 3D Systems Страницы: 8

Бренд: 3D Printing Systems Страницы: 54

Бренд: Radio Shack Страницы: 62

WorkCentre 4265

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 11

Бренд: Rena Страницы: 59

Бренд: Star Страницы: 24

Бренд: Parkside Страницы: 104

Бренд: Oki Страницы: 204

Бренд: Jolimark Страницы: 65

Бренд: MHM Страницы: 52

Stylus Color C70

Бренд: Epson Страницы: 2

Stylus Color C80

Бренд: Epson Страницы: 11

Stylus Color C60

Бренд: Epson Страницы: 3

Stylus Photo 1270

Бренд: Epson Страницы: 2

StylusRIP Professional (Stylus Photo 2200

Бренд: Epson Страницы: 10

Stylus Photo R360

Бренд: Epson Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды