Ricoh AFICIO AP306 Скачать руководство пользователя страница 132

Страница: 132 / 382

Draft 2000/06/22

Troubleshooting

This message appears when you use the duplex printer.

Paper Tray : Not Set Cor-
rectly

The paper tray is not in-
stalled correctly.

Install the paper tray cor-
rectly.

The tray on the paper feed-
ing path is not set correctly
when the printer receives
the print job.

Install the paper tray cor-
rectly. The printer will re-
start printing
automatically.

PCU : Not Set Correctly

The photoconductor unit is
not installed in the printer.

Install the photoconductor
unit correctly.

⇒

P.74

“Re-

placing the Photoconductor
Unit”

Ready

Printer works properly.

—

Rear Cover Open

The rear cover is open.

Close the rear cover.

⇒

the

"Setup Guide" that comes
with the printer

Time to Change Charger

It is time to replace the
charger.

Replace the charger.

⇒

P.80

“Replacing the Charger”

Time to Change Fusing
Unit

It is time to replace the fus-
ing unit.

Contact your sales or ser-
vice representative.

Time to Change PCU

It is time to replace the pho-
toconductor unit.

If printed side gets dirty,
replace the photoconduc-
tor unit.

⇒

P.74

“Replacing

the Photoconductor Unit”

Toner : Not Set Correctly

The toner cartridge is not
installed correctly.

Install the cartridge cor-
rectly.

⇒

P.71

“Replacing

Toner Cartridge”

Warming Up

The printer is preparing for
printing.

Wait until the printer is
warmed up.

Waste Toner is Full

The waste toner bottle is
full.

Replace the waste toner
bottle.

⇒

P.78

“Replacing

the Waste Toner Bottle”

Waste Toner is Nearly Full The waste toner bottle is

nearly full.

Replace the waste toner
bottle.

⇒

P.78

“Replacing

the Waste Toner Bottle”

WasteToner : Not Set Cor-
rectly

The waste toner bottle is
not installed correctly.

Install the waste toner bot-
tle correctly.

⇒

P.78

“Re-

placing the Waste Toner
Bottle”

xxx Toner is Empty

The indicated toner is low
or has run out.

Replace the indicated toner
cartridge.

⇒

P.71

“Replacing Toner

Cartridge”

Message

Description

Comments

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды