Ricoh AFICIO AP306 Скачать руководство пользователя страница 269

Страница: 269 / 382

Draft 2000/06/22

vii

Configuring the printer as a print server

A dedicated NetWare print server is not required because the printer can be con-
figured as a print server.

The actual procedures for configuring the printer differ depending on the ver-
sion of NetWare.
• NetWare 3.x

⇒

P.52

“Setting Up as a Print Server”

• NetWare 4.x, 5

⇒

P.59

“Setting Up as a Print Server”

Configuring the printer as a remote printer

If a dedicated NetWare print server is being used, the printer should be config-
ured as a remote printer.

The actual procedures for configuring the printer differ depending on the ver-
sion of NetWare.
• NetWare 3.x

⇒

P.55

“Setting Up as a Remote Printer”

• NetWare 4.x, 5

⇒

P.63

“Setting Up as a Remote Printer”

NetWare
File Server

Print Server

Windows 95 / 98

Windows 2000

Windows NT 4.0

NetWare
Print Server

NetWare
File Server

Remote Printer

Windows 95 / 98

Windows 2000

Windows NT 4.0

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды