Ricoh AFICIO AP306 Скачать руководство пользователя страница 353 | Manualshive

Страница: 353 / 382

background image

Draft 2000/06/22

Remote Maintenance by telnet

79

6

-

Address

❖

Subnet Mask

A number used to mathematically “mask” or hide the IP address on the net-
work by eliminating those parts of the address that are alike for all the ma-
chines on the network.

❖

Default Gateway Address

A gateway is a connection or interchange point that connects two networks.
A gateway address is for the router or host computer used as a gateway.

Note

❒

To get the above addresses, contact your network administrator.

Access Control

Use the access command to view and configure access control.

❖

Reference

msh> access

❖

Configuration

msh> access

parameter address

Note

❒

The Access Control Address and the Access Control Mask are used to limit
access to the computer used for printing by denying access to users based on
their IP address. If it is not necessary to limit access, set the Access Control
Mask to “0.0.0.0”.

❒

When the Access Control Address matches the masked result of the IP ad-
dress computer attempting to print, print jobs from that IP address will be ac-
cepted by the Network Interface Board.

Parameter

Meaning

control

Access Control Address

mask

Access Control Mask

«
...
351
352
353
354
355
...
»

Содержание AFICIO AP306































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFICIO AP306

PIXMA MX882 Series

Бренд: Canon Страницы: 34

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 913

Laser Class 700 Series

Бренд: Canon Страницы: 30

Laser Class 700 Series

Бренд: Canon Страницы: 6

Laser Class 700 Series

Бренд: Canon Страницы: 6

Laser Class 700 Series

Бренд: Canon Страницы: 108

PIXMA MX860 series

Бренд: Canon Страницы: 9

imagePROGRAF iPF9400

Бренд: Canon Страницы: 8

PIXMA MX860 series

Бренд: Canon Страницы: 93

Бренд: Canon Страницы: 20

Бренд: Canon Страницы: 30

Бренд: Canon Страницы: 2

Бренд: DataCard Страницы: 17

Бренд: DataCard Страницы: 24

T2150 SprintPro

Бренд: Tally Страницы: 124

Бренд: TierTime Страницы: 28

Бренд: Olympus Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды