Ricoh AFICIO AP306 Скачать руководство пользователя страница 163

Страница: 163 / 382

Draft 2000/06/22

Replacing Consumables

❒

Disposal can take place at our au-
thorized dealer or at appropriate
collection sites.

❒

Dispose of used ozone filters as
general burnable refuse.

Turn off the printer's power switch.

Replace the oil bottle.

Remove the green cap from the
new oil bottle.

Important

❒

Hold the clear cap while
turning the green cap. Do not
remove the clear cap.

Open the fuser oil bottle cover
of the printer.

Remove the used oil bottle
from the printer carefully.

Insert the new oil bottle into
the oil bottle case.

Close the fuser oil bottle cover.

Important

❒

The fuser oil bottle cover
should be kept closed.

Replace the ozone filter on the
rear of the printer.

Remove the ventilator hole
cover.

❖

Simplex printer

❖

Duplex printer

TFWX031E

TFWX090E

TFWX100E

ZBGX050E

ZBGX060E

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды