Ricoh AFICIO AP306 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 382

background image

Draft 2000/06/22

Troubleshooting

76

4

H

Holding the green inset grips of
the new photoconductor unit, in-
sert the unit into the photocon-
ductor unit holder.

When inserting the photoconduc-
tor unit, be careful not to damage
the surface of it.

Note

❒

The white powder on the photo-
conductor unit is to protect it af-
ter installation into the printer.
This white powder does not
have any adverse effect on the
interior of the printer.

I

Holding the green inset grips of
the new photoconductor unit,
push the unit back to its original
position.

J

Fasten the screws using the screw
driver to fix the photoconductor
unit.

K

Close the front cover.

Confirm that the front cover closes
properly.

L

Turn on the printer’s power switch.

Replacing the Fuser Oil Bottle
and Ozone Filter

Replace the oil bottle and ozone filter
whenever the following messages ap-
pear on the panel display.

IPDL-C

Add FuserOil

Add Fuser Oil

There are the fuser oil bottle and the
ozone filter in the Fuser Oil Type306
includes a fuser oil bottle and ozone
filters.

R

WARNING:

R

CAUTION:

Important

❒

There are three ozone filters in this
printer. Two of them are set inside
in the front, one of them is set in
the rear. Be careful when replacing
the ozone filters as the front side
filter is a different shape from the
rear side filter.

TFWX305E

•

Do not incinerate the oil bottle.
This action could cause a fire
or getting burned.

•

Spilt oil is very slippery. If oil
is spilt, wipe it with alkaline
cleaner. Otherwise, the oily
surfaces can create the dan-
ger of slipping and personal
injury.

•

When accessing the inside of the
machine, do not touch any sec-
tions other than those specified
in this manual. If you do, it might
result in receiving a burn or inju-
ry.

«
...
160
161
162
163
164
...
»

Содержание AFICIO AP306































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFICIO AP306

Бренд: MakerBot Страницы: 48

Бренд: Oki Страницы: 268

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 202

Бренд: Oki Страницы: 201

Бренд: Oki Страницы: 103

Бренд: Oki Страницы: 256

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 63

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 616

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 138

Microline 320 Turbo D1

Бренд: Oki Страницы: 2

ML320 Epson/IBM

Бренд: Oki Страницы: 32

Бренд: Oki Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды