Ricoh AFICIO AP306 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 382

background image

Draft 2000/06/22

Troubleshooting

38

4

Error & Status Messages on the Operation Panel

Important

❒

If the error message that is not included in the following table appears on the
panel display, turn the printer off and on. If this does not clear the error mes-
sage, write down the error number and the message, and contact your sales
or service representative.

Note

❒

The panel display can show only one error message at a time. Printing a con-
figuration page shows all current printer errors.

⇒

P.99

“Printing the Configu-

ration Page”

❒

For more information about the IPDL-C printer driver, see the printer driver's
Help.

❒

For more information about the RICOH-SCRIPT2 printer driver, see the “Op-
erating Instructions” for RICOH-SCRIPT2 included as a PDF file on the CD-
ROM.

Message

Description

Comments

Add Fuser Oil

(on the upper line)

The fuser oil bottle is emp-
ty.

Replace the fuser oil bottle.

⇒

P.76

“Replacing the Fuser

Oil Bottle and Ozone Filter”

Add Fuser Oil

(on the lower line)

Fuser oil is low. You can
print about 200 or /more
pages after this message
appears.

Replace the fuser oil bottle.

⇒

P.76

“Replacing the Fuser

Oil Bottle and Ozone Filter”

Add Toner

Please Wait

The toner cartridge is being
prepared for replacement.

Wait for a while.

Add Toner

xxx

The indicated toner runs
out.

Replace the indicated toner
cartridge.

⇒

P.71

“Replacing Toner

Cartridge”

Call Service

SC:xx

There is a malfunction in
the printer.

Turn the printer off and on.

If this does not clear the
problem, contact your sales
or service representative.

Change Fuser

It is time to replace the fus-
ing unit.

Contact your sales or ser-
vice representative.

Change PCU.

It is time to replace the pho-
toconductor unit.

If prints are dirty, replace
the photoconductor unit.

⇒

P.74

“Replacing the Photo-

conductor Unit”

«
...
122
123
124
125
126
...
»

Содержание AFICIO AP306































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFICIO AP306

MultiPASS L6000

Бренд: Canon Страницы: 251

MultiPASS C5500

Бренд: Canon Страницы: 24

MultiPASS L6000

Бренд: Canon Страницы: 24

Laser Class 700 Series

Бренд: Canon Страницы: 221

Бренд: Acadian Robotics Страницы: 2

Бренд: Fastjet Страницы: 52

Бренд: SEH Страницы: 20

DiMAGE Scan Elite 5400 II

Бренд: Konica Minolta Страницы: 38

WorkCentre BookMark 40

Бренд: Xerox Страницы: 12

Бренд: Edimax Страницы: 93

3500DN - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 6

PR-INT-MX-RAVAS-ABLE

Бренд: Ravas Страницы: 26

Бренд: 3nStar Страницы: 44

Бренд: SEWOO Страницы: 24

Бренд: Oki Страницы: 246

Бренд: Konica Minolta Страницы: 108

Бренд: TEC Страницы: 92

Бренд: MHM Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды