Ricoh AFICIO AP306 Скачать руководство пользователя страница 128

Страница: 128 / 382

Draft 2000/06/22

Troubleshooting

B0:Error

An error has occurred in
the optional memory unit.

Turn the printer off and on.
Then, try to print again.

Turn off the printer. Re-
move and reinstall the
memory unit and turn on
the printer. Then, try to
print again.

Turn off the printer. Re-
move the memory unit and
turn on the printer. Then,
try to print again.

Note

❒

If you remove the mem-
ory unit, you must re-
configure the printer
driver.

⇒

the "Setup

Guide" that comes with
the printer

❒

In this case, you might
not be able print com-
plex print jobs.

B1:Error

An error has occurred in
the standard parallel inter-
face.

Contact your sales or ser-
vice representative.

B3:Error

The printer setting is
wrong.

Reset the printer using
"Menu Reset" of the "Main-
tenance" menu.

⇒

P.83

“Using the Operation Panel”

B5:Error

An error has occurred in
the RICOH-SCRIPT2 mod-
ule.

Contact your sales or ser-
vice representative.

B6:Error

An error has occurred in
the optional parallel inter-
face board.

Turn off the printer. Re-
move and reinstall the op-
tional parallel interface
board and turn on the
printer. Then, try to print
again.

Message

Description

Comments

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды