Ricoh AFICIO AP306 Скачать руководство пользователя страница 150

Страница: 150 / 382

Draft 2000/06/22

Troubleshooting

Open the back guide in the du-
plex tray as shown in the illustra-
tion, and then the remove the
misfed paper.

Open the guide under the back
guide as shown in the illustration,
and then the remove the misfed
paper.

Important

❒

When removing misfed paper,
handle the guides with great
care.

Close the guides opened in steps

and

Slide the duplex tray completely
into the printer.

Important

❒

Be sure to insert the duplex tray
completely. If not fully inserted,
misfeeds might occur, or the
front cover might touch the pa-
per tray.

When the Message "Remove
Misfeed From Rear Cover"
Appears

CAUTION:

Open the rear cover, and then re-
move the misfed paper.

Close the rear cover.

Push the center of rear cover until
it rocks.

ZBGY040E

ZBGY041E

•

When removing misfed paper,
do not touch the fusing section
because it could be very hot.

ZBGY090E

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды