Ricoh AFICIO AP306 Скачать руководство пользователя страница 40

Страница: 40 / 382

Draft 2000/06/22

Installing Options

Remove the two screws, and re-
move the interface board cover.

Note

❒

A coin can be used to remove
the screws.

Align the interface with the con-
nector, insert it until it clicks into
place. Then fasten it with the
screws removed in step

Note

❒

If you want to install a different
type of interface board in the
other slot while the cover is
open, repeat steps

and

Attach the controller board cover
to its original position, and fasten
it with the screws removed in step

If you use the duplex printer,
close the duplex unit and then
fasten it with the screws removed
in step

Connect all cables removed in
step

Plug the printer's power cord
back into the printer and the out-
let. Turn on the printer's power
switch.

Print a configuration page to con-
firm that the interface board is
properly installed.

Reference

⇒

"Printing the Configuration

Page" in the "Printer Reference"
included as a PDF file on the
CD-ROM

ZBGP040E

ZBGP041E

ZBGP011E

ZBGH011E

Содержание AFICIO AP306






























































































































































































































































































































































































Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды

Ricoh AFICIO AP306, Руководство по установке

Результаты поиска

Содержание AFICIO AP306

Отзывы:

Похожие инструкции для AFICIO AP306

Бренды по названию

Популярные бренды