Ricoh AFICIO AP306 Скачать руководство пользователя страница 359 | Manualshive

Страница: 359 / 382

background image

Draft 2000/06/22

Remote Maintenance by telnet

85

6

❖

Configuring IPP user authorization

Use the following command:

ipp user

The following message appears.

Input user number (1 to 10):

Type the number, user name and password.

IPP user name:user1
IPP password:*******

After configuring the settings, the following message appears.

User configuration changed.

Changing the password

Use the passwd command to change the remote maintenance password.

Important

❒

Be sure not to forget or lose the password.

Note

❒

The default factory password is “password”.

A

Type “passwd”.

msh> passwd

B

Type the current password.

Old password:

C

Type the new password.

New password:

Note

❒

The password must consist of 3 to 8 alphanumeric characters and symbols.
Upper and lower case characters are considered unique. For example, R is
different from r.

❒

The password is the same as that used in the configuration of the Network
Interface Board using a Web Browser and that used in the NIB Setup Tool.
If you change a password from telnet, the other passwords are also
changed.

D

Type the new password once again.

Retype new password:

«
...
357
358
359
360
361
...
»

Содержание AFICIO AP306































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AFICIO AP306

Бренд: Qls Страницы: 53

Бренд: Xerox Страницы: 36

CLP-680ND: CLP-775ND

Бренд: Samsung Страницы: 2

Бренд: SPRT Страницы: 28

Бренд: Xerox Страницы: 89

imageRUNNER ADVANCE C3330 Series

Бренд: Canon Страницы: 5

imagePROGRAF TA-30

Бренд: Canon Страницы: 49

Бренд: Canon Страницы: 210

Color imageCLASS MF8180c

Бренд: Canon Страницы: 34

Бренд: Citizen Страницы: 32

Бренд: A&D Страницы: 32

Бренд: Lexmark Страницы: 57

Бренд: oti Страницы: 33

Бренд: idp Страницы: 63

Бренд: Cashino Страницы: 61

Бренд: 3nStar Страницы: 44

Бренд: Z Corporation Страницы: 12

Бренд: Z Corporation Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды