OmniTek OTR 1001 Скачать руководство пользователя страница 247 | Manualshive

Страница: 247 / 390

background image

OmniTek OTR 1001 User Guide, v3.1

N-9

The test sequence contains many elements that are useful for testing and analysing the
performance of a video system, however for the purposes of the audio/video delay measurement
it has two characteristics that are of special importance – an embedded audio tone (in the case of
the PCM-only sequence this tone needs to be added when the sequence is run) and a binary
frame count displayed in the top left-hand corner of each frame as a sequence of yellow squares.

When the clock hand reaches the top (frame 0), an

audio pulse is generated for 1 frame duration

This gives a binary count of

the test sequence

Figure N-9:

OmniTek Test Sequence

The Analyzer software extracts the binary frame count from the input video image. It also
detects the embedded audio tone. The relative timing of the audio tone to the first video frame in
the sequence indicates the delay between audio and video components.

Playing the Test Sequence

The supplied test sequences can only be played by the generator of an OmniTek OTM, OTR or
LAB system. However, the output from the Generator can then be recorded on a recording
device that also records blanking – e.g. a tape or disk recorder – and that recording subsequently
used in place of OmniTek system.

Control Panel

Mouse & Keyboard

To run the test sequence on an OTR 1001:

(

Note:

Equivalent steps are given in the OTM 1000 , OTR 1003 and OmniTek LAB user guides.)

1.

Set the OTR to generate output in the appropriate video standard as described in Section P.2.

2.

Load all the frames of the special A/V Delay Test Sequence that is applicable to the video
format that is under test (see ‘Test Sequences’ above).

For information on loading a sequence, see Section R.2.

3.

Call up the Properties of the Test Sequence and check that the

Resize type

for this pattern is

set to

None

. (See Section Q.5)

4.

Where the

TSA

(PCM-only) test sequence is being used

, set the

Audio Tone Generator

to

generate a tone on channel 1 set for 8kHz, -18dB (see Section Q.6) and set the associated

Click Mode

to

Mutes except on frame 1

.

These settings are essential for correct operation.

5.

Play the Test Sequence as a continuous loop.

Note:

Where the sequence is recorded to tape/disk, it is sensible to record at least a minute of the

repeating sequence to make operation and measurement easier.

«
...
245
246
247
248
249
...
»

Содержание OTR 1001







































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OTR 1001

Бренд: ABB Страницы: 14

Бренд: NEC Страницы: 54

Бренд: Wavetek Страницы: 74

Бренд: Fairchild Страницы: 16

Бренд: Abicor Binzel Страницы: 92

Бренд: Jacobsen Страницы: 20

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: zarges Страницы: 36

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: OHAUS Страницы: 84

Бренд: Rainin Instrument Страницы: 16

Бренд: L-Acoustics Страницы: 5

Бренд: Jumil Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды