manualshive.com logo in svg

OmniTek OTR 1001, Руководство пользователя

Поделиться
Скачать
OmniTek OTR 1001 Скачать руководство пользователя страница 84

 

 

OmniTek OTR 1001 User Guide, v3.1a 

E-12 

Configuration Issues 

The  following  Configuration  settings  affect  how  the  Vectorscope  is  displayed. 

Note:

  Further 

settings are required where 3D images are analysed: these are described in Section I.8. 

Error Mask 

The OTR 1001 allows you to specify a number of lines from the top and bottom of the display 
and  a  number  of  pixels  from  the  left  and  right  edge  that  can  be  omitted  from  the  checking 
process. This is referred to as an Error Mask and it is defined on the 

Video Config

 page of the 

Config  window.  Its  purpose  is  to  avoid  producing  misleading  results  as  a  result  of  including 
video data that has been corrupted by the sync. 

Composite Matrix 

Different  matrices  may  be  applied  in  producing  the 
composite  version  of  the  Vectorscope  display.  The  OTR 
can  either  be  set  to  select  the  appropriate  matrix 
automatically,  based  on  the  input  video  standard  or  it  can 
be set to select a particular composite matrix. The selection 
is  made  through  the 

Composite  Matrix  Type

  option 

offered on the 

Video Config

 page of the Config window. 

Display Properties 

Other  aspects  of  the  Vectorscope  are  determined  by  the 
tile’s  properties,  a  complete  read-out  of  which  is  given  in 
the  Properties  control  (Control  Panel:  press  PROPS  to 
display). Shortcuts to the most-commonly required settings 
are  provided  through  the  Button  Bar  (Control  Panel:  press 
GENERAL  or  OTHER;  Mouse/Keyboard:  click  on  tile  to 
display). 

Mode of Operation 

The 

Filter

  control  selects

 

how  the  incoming  data  is 

sampled. The choice offered is between a 

Flat

 filter, a 

Low 

Pass

  filter  or 

No  Interpolation

.  The  Button  Bar  option 

cycles  round  these  three  options.  When  Labels  are  shown 
(see 

Show Labels

 below), the type of filtering that is being 

applied  is  shown  in  the  bottom  right-hand  corner  of  the 
display.  The  Button  Bar  option  switches  between 
Interpolation On (button highlighted) and Interpolation Off.  

Interpolation  is  usually  enabled  but  users  should  be  aware 
that it can occasionally produce out of range results. Where 
these occur, you may prefer to turn the interpolator off. 

 

Button Bar 

 

 

 

 

 

 

 

 

 

 

 

 

Figure E-9: 

Vectorscope 

Properties. 

Содержание OTR 1001







































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды