manualshive.com logo in svg

OmniTek OTR 1001, Руководство пользователя

Поделиться
Скачать
OmniTek OTR 1001 Скачать руководство пользователя страница 234

 

 

OmniTek OTR 1001 User Guide, v3.1 

M-10 

Vertical Gain and Vertical Offset 

The 

V  Gain

  and 

V  Offset

  controls  determine  the  vertical  scaling  and  the  positioning  of  the 

display. (The 

V Gain

 option on the Button Bar cycles through the available scalings.) 

Note:

 The 

V Gain

 control is disabled in Auto Measure mode. 

Cursors 

The  Cursor  options  control  the  cursor-pairs  that  can  be  used  to  measure  time  differences  and 
voltage differences between any two points on the Eye Diagram.  

The 

Show Cursors

 option in the Properties control provides overall control of the display of any 

cursors  over  the  display,  while  the 

Cursors

  option  on  the  Button  Bar  switches  between  these 

cursors (and associated markers such as those marking the 20% and 80% level) being shown and 
being hidden. 

The

 Time Cursors

 and 

Voltage Cursors

 tick selections separately control the display of a pair 

of cursors providing difference measurements in the horizontal (

time

) direction and the vertical 

(

voltage

)  direction.  When  the  cursors  are  displayed,  a  read-out  of  the  times  and  voltage 

differences measured is shown in the top right-hand corner of the screen as 

dx

 and 

dy

 values. 

Visualisation 

The 

Gain

  control  adjusts  the  intensity  of  the  displayed  signal  (as  a  percentage  of  the  received 

signal level).

 Note: 

This control is disabled in Auto Measure mode. 

The 

Persistence

 setting sets the rate at which the displayed data decays. Larger values have the 

result of smoothing out time variations. 

Note: 

This control is disabled in Auto Measure mode. 

The 

Gamma

  setting  applies  gamma  encoding  to  the  signal.  A  setting  of  100  corresponds  to  a 

gamma value of 1. Values below 100 emphasise differences in low-level signal strengths, while 
values over 100 emphasise differences in high-level signal strengths.  

The 

Colour

 setting selects the colour used for the waveform trace (out of 

Cyan

, 

Green

, 

White

 

or  ‘

Temperature  Ramp

’).  The 

Colour

  option  in  the  Button  Bar  cycles  through  the  available 

colours.

 

The 

CRT Emulation

 option applies a special filter to the waveform data to emulate how the Eye 

might be displayed on a CRT-based waveform monitors. Selecting the 

CRT Emulation

 option 

on the Button Bar switches this option between On and Off. 

Show Graticule

 controls the display of the underlying Graticule. 

The 

Jitter Meter

 option controls how the Jitter meter is displayed. 

Equalisation 

The 

Equalised

 tick box sets whether the signal is viewed after it has passed through an internal 

cable equalizer that compensates for loss introduced by the cable. Ticking the 

Equalised

 option 

is normally only worth doing where the signal is otherwise approximately jitter free. The Button 
Bar  option  switches  this  setting  between  On  and  Off. 

Note: 

This  control  is  disabled  in  Auto 

Measure mode. 

Eye Sample Rate 

Sets  the  timebase  for  the  pattern  by  selecting  the  number  of  eyes  to  be  formed.  The  Button  Bar 
option cycles through the available settings.

 Note: 

This control is disabled in Auto Measure mode. 

Auto Measure 

Selects  the  OTR’s  automatic  measurement  mode.  The  Button  Bar  option  switches  this  setting 
between On and Off. 

Содержание OTR 1001







































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды