OmniTek OTR 1001 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 390

background image

OmniTek OTR 1001 User Guide, v3.1a

E-13

The

TRS Passthrough

tick selection enables the inclusion of the TRS in the display.

The

Bar Targets

option lets you select between comparing the trace against a 100% graticule

and comparing it against a 75% graticule. The Button Bar option switches between the two
graticules.

The

Line Mode

control selects between displaying the waveform of a single line (picked out by

the crosshair cursor) or multiple lines. The Button Bar option switches between these two
settings. (For details of the lines selected, see Section E.2 ‘Focus of Analysis’.) Where

Single

line

is selected, the line being analysed is shown in the bottom left-hand corner of the display.

The

Mag

option in the Properties control offers the choice of 1x, 2x, 5x or whatever customised

(xx.xx) zoom was last selected, while the

Mag

option on the Button Bar switches between 1x

and the last of the other scalings to have been selected. (Customised zooms are selected either by
using the HORIZ knob on the Control Panel or by clicking and dragging.

Note:

Pressing HORIZ

returns the scaling to 1x.)

The

Colour Mode

control selects between displays based on the SDI input or on the Composite

version (see Waveform View above). The Button Bar option switches between these options.

Note:

The OTR automatically switches the graticule to match the selected Colour Mode.

The

Dither Mode

option offers a choice of Dither mode between 8bit, 10bit and 12bit (where

supported).

Luma Mask

When

Luma Mask

is selected, the display becomes limited to those pixels whose luma value

lies between the associated

Minimum

and

Maximum

settings. The Button Bar option switches

between the two displays.

Visualisation

The

Gain

control sets the intensity of the displayed waveform (as a percentage of the received

signal level).

The

Persistence

setting sets the rate at which the displayed data decays. Larger values have the

result of smoothing out time variations.

The

Gamma

setting applies gamma encoding to the waveform. A setting of 100 corresponds to a

gamma value of 1.

The

Colour

setting selects the colour used for the waveform trace, out of

Cyan

,

Green

,

White

or ‘

Temperature Ramp

’.

The

CRT Emulation

option applies a special filter to the waveform data to emulate the look that

is typical of analog CRT-based waveform monitors.

The

Show Graticule

option controls the display of the underlying grid and associated

information.

The graticule normally scales with the

Mag

setting. Ticking the

Fixed Graticule

option keeps

the graticule for x1 for all magnifications.

The

Show Labels

option controls the display of labels and other additional information.

(For information about the

3D View

option, see Section I.9.)

«
...
83
84
85
86
87
...
»

Содержание OTR 1001







































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OTR 1001

Бренд: Sagola Страницы: 8

Бренд: Quincy lab Страницы: 4

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: Kärcher Страницы: 148

Бренд: ACS Страницы: 28

Pro hunter 2525

Бренд: SprotDog Страницы: 28

Бренд: ICON Страницы: 24

CB Ohio Special 100 HP

Бренд: CleaverBrooks Страницы: 200

LEDP5W-60XC-1227

Бренд: Larson Electronics Страницы: 2

Бренд: Lennox Страницы: 20

50A10 Omo Immobil

Бренд: Otto Bock Страницы: 144

Бренд: Gardena Страницы: 8

SkyWriter HPX M-5

Бренд: X-laser Страницы: 65

SC-88 Sound Canvas

Бренд: Roland Страницы: 146

Бренд: TAPKO Страницы: 2

Бренд: Amico Страницы: 19

Бренд: Biotage Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды