Nord Drivesystems SK 200E Series, Руководство пользователя

Страница: 184 / 265

NORDAC SK 200E Manual
184 Subject to technical alterations BU 0200 GB
Parameter
{Factory setting}
Setting value / Description / Note Device Supervisor
Parameter
set
P542
[-01]
[-02]
Set analog out put
S
0.0 ... 10.0 V
{ all 0.0 }
[-01] = First IOE, AOUT of the first I/O extension (SK xU4-IOE)
[-02] = Second IOE, AOUT of the second I/O extension (SK xU4-IOE)
... only with
SK CU4-IOE or
SK TU4-IOE The analog output of the FI can be set with this function, independently of the actual operating
state. To do this, the relevant analog output must be set to the function "External control"
(P418 = 7).
This function can either be used manually or in combination with a bus control. The value set
here will, once confirmed, be produced at the analog output.
P543
[-01]
...
[-03]
Actual bus value 1… 3
S P
In this parameter the returned value on bus actuation can be selected.
NOTE: For further details, please refer to the relevant bus manual or the description for
(P418). (Values from 0% … 100% correspond to 0000
hex
… 4000
hex
)
For standardisation of the actual values: See also (Section 9.10).
[-01] = Actual bus value 1
[-02] = Actual bus value 2 (only for PPO type 2 or 4)
[-03] = Actual bus value 3 (only for PPO type 2 or 4)
Possible setting values:
0 ... 22
{ [-01] = 1 }
{ [-02] = 4 }
{ [-03] = 9 }
0 = Off
1 = Actual frequency
(x=4000
hex
*f[Hz]/(P105))
2 = Actual speed
(x=4000
hex
*n(rpm]/(P202))
3 = Current
(x=4000
hex
*I[A]/(P203))
4 =
Torque current (100% = P112)
(x=4000
hex
*Iq[A]/(P112)*100/
√
((P203)²+(P209)²)
5 = Digital IO status
4
6 = ... 7 reserved
8 = Setpoint frequency
(x=4000
hex
*fs[Hz]/(P105))
9 = Error code
10 = ... 11 reserved
12 = Bus IO Out Bits 0..-7
13 = ... 16 reserved
17 = Analog input value 1
(AIN1 of the first I/O extension
SK xU4-IOE (P400 [-03]))
18 = Analog input value 2
(AIN2 of the first I/O extension
SK xU4-IOE (P400 [-04]))
19 = Setpoint freq uency master value
(P503)
(x=4000
hex
*fs[Hz]/(P105))
20 = Set point freq uency after ramp ,
master value
(x=4000
hex
*fsnr[Hz]/(P105))
21 = Act ual freq uency w ith o ut slip master
value
(x=4000
hex
*f-f2[Hz]/(P105))
22 = Speed from speed encoder
(x=4000
hex
*n[Hz]/(P105)/(60/p))
p=pole-pair number,
Determined from (P201) and (202))
4
The assignment of the dig. inputs for P543 = 5
Bit 0 = DigIn 1
(FI)
Bit 1 = DigIn 2
(FI)
Bit 2 = DigIn 3
(FI)
Bit 3 = DigIn 4
(FI)
Bit 4 = PTC input
(FI)
Bit 5 = DigIn 5
(DI1, 1. SK…IOE)
Bit 6 = DigIn 6
(DI2, 1. SK…IOE)
Bit 7 = DigIn 7
(DI3, 1. SK…IOE)
Bit 8 = DigIn 8
(DI4, 1. SK…IOE)
Bit 9 = reserved Bit 10 = reserved Bit 11 = reserved
Bit 12 = DigOut 1
(FI)
Bit 13 = mech. brake
(FI)
Bit 14 = DigOut 2
(DO1, 1. SK…IOE)
Bit 15 = DigOut 3
(DO2, 1. SK…IOE)