Nidec COMMANDER S100 Скачать руководство пользователя страница 105

Страница: 105 / 118

Drive parameters Communications

Commander S100 User Guide

105

E018

Tune Interrupted

The drive was prevented from completing an auto-tune, because either the drive enable or the drive run signals were
removed.

Recommended actions:

•

Ensure the drive enable signal is active for the entire auto-tune. This can be checked using

Sequencer Input and

Output Indicators

(P1.11)

•

Ensure a run signal (Run Forward, Run Reverse or Run) is active for the entire auto-tune. This can be checked using

Run & Direction Indicators

(P1.12)

•

If these signals are supplied by a digital input, check the states of the IO using

Digital IO Indicators

(P1.25)

E020

Motor Temp

The drive has estimated that the motor has become too hot based on the

Motor Rated Current

(P3.01) and

Thermal

Protection Action

(P3.21).

Motor Thermal Percentage

(P1.22) displays the motor temperature as a percentage of the maximum value. The error

occurs when this parameter reaches 100 %.

Recommended actions:

•

Ensure the load is not jammed / sticking

•

Check the load on the motor has not changed

•

Ensure the motor rated current is correct.

E021

Drive Temp 1

An IGBT junction over-temperature has been detected.

Recommended actions:

•

Check enclosure temperature

•

Check enclosure / drive fans are still functioning correctly

•

Clean the fan filter if being used

•

Check enclosure ventilation paths

•

Check enclosure door filters

•

Increase ventilation

•

Reduce duty cycle

•

Increase acceleration / deceleration rate parameter values

•

Reduce motor load

•

Ensure all three supply phases are present and balanced

•

Confirm the drive is correctly sized for the application

•

Use a drive with larger current / power rating

E023

Drive Temp 2

A power stage over-temperature has been detected.

Recommended actions:

•

See Drive Temp 1

E027

Drive Temp 3

A D.C. bus component over temperature has been detected.

Recommended actions:

•

See Drive Temp 1.

E028

An In 1 Current

A current loss was detected in T2 analog input 1 and the input type is set to 4-20 mA Error (6). Loss of input is detected if
the current falls below 3 mA.

Recommended actions:

•

Check control wiring is correct

•

Check control wiring is undamaged

•

Check T2

Analog Input 1 Type

(P6.01)

•

Check the current signal is present and greater than 3 mA

Error

Diagnosis

Содержание COMMANDER S100























































































































Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды

Nidec COMMANDER S100, Руководство пользователя

Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды