Nidec COMMANDER S100 Скачать руководство пользователя страница 95

Страница: 95 / 118

Commander S100 User Guide

P6.20

T15 Digital Input 5 Function Select

Range:

0 to 20

Default:

10 (Reference Switch Bit 0)

Selects the digital input function of the selected control terminal if it is in digital input mode.

Notes on function selection:

•

Selecting the

Run Permit (Not Stop)

function (4) automatically enables a latch on the Run inputs (

Run Forward, Run Reverse,

and

Run

), see

Run & Direction Indicators

(P1.12). Providing the

Run Permit

input is active, activation of the Run inputs is latched so that a momentary switch

can be used to start the drive. When

Run Permit

is made inactive (Stop), all latches are cleared, and no Run signal is accepted.

•

Run Forward

Run Reverse

is made active, the Reverse function will be ignored i.e. explicit

Run Forward

and

Run Reverse

signals

override the direction selection.

•

A Run signal overrides a Jog signal.

The value of these parameters can be set by

Run/Stop Configuration

(P6.13).

Value

Function

Description

None

No Digital Function

Hardware Enable

If selected, is used to enable or disable the drive

Run Forward

Commands the drive to run forward

Run Reverse

Commands the drive to run reverse

Run Permit (Not Stop)

Permits a Run signal when set, resets any run latch when clear (enables latching when selected as a
function)

Forward Limit Switch

Prevents a run in the forward direction

Reverse Limit Switch

Prevents a run in the reverse direction

Up/Down % Increase

Increases the Up/Down percentage

Up/Down % Decrease

Decreases the Up/Down percentage

Up/Down % Reset

Resets the Up/Down percentage

Reference Switch Bit 0

Used to select Reference 1, 2, 3 or 4

Reference Switch Bit 1

Used to select Reference 1, 2, 3 or 4

Ramp Select

Used to select Acceleration and Deceleration Rate 1 or 2

PID Enable

Enables and disables the PID controller. If no Hardware Enable is required, this configuration should
not be selected

External Error

Used to generate an Error from an external condition

Drive Reset

Used to reset the drive from an error condition

Run

Commands the drive to run

Reverse

Reverses the direction

Jog Forward

Commands the drive to jog forward

Jog Reverse

Commands the drive to jog reverse

Fire Mode

Commands the drive to run at the Fire Mode Reference, ignoring enable and run signals. See Fire
Mode Reference parameter for more information

NOTE

Содержание COMMANDER S100























































































































Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды

Nidec COMMANDER S100, Руководство пользователя

Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды