Nidec COMMANDER S100 Скачать руководство пользователя страница 42

Страница: 42 / 118

Commander S100 User Guide

5.5 Understanding the menu structure

The drive parameters, status, and monitoring values can be found within three modes: Status, Parameter Select and Parameter Edit.

Status

The primary mode of the drive that is used to provide users with an indicator to show the current status of the system, see Table 5-2. If the keypad is

to be used to provide a drive frequency reference, the display must be in

Status

for the user to be able to edit the reference using the UP

and

DOWN

buttons. If the drive is running,

Status

will show one of five monitoring parameters and the user can rotate between these by holding the

Settings

button

. The monitoring parameters that can be shown are as follows:

Ramp Output (Hz)
Output Voltage (V)
Output Current (A)
Output Speed (rpm)
Drive Load (%)

Parameter select

From

Status

users can move to

Parameter Select

by pressing the

Settings

button

Parameter Select

allows the user to navigate through the drive

parameters. Users can scroll up and down the list of individual parameters by pressing the

and

DOWN

buttons or they can switch between

different menus by holding the

button

to move to the next menu or the

DOWN

button

to move to the previous menu.

Parameter edit

Once the desired parameter has been located in

Parameter Select

, the parameter value can be viewed or edited by pressing the

Settings

button

The units of the selected parameter will be shown on the display. To edit the value of the parameter, the

DOWN

buttons should be

pressed to increase or decrease the value as appropriate. Holding the

DOWN

buttons will move the cursor left or right

respectively. The digit currently being edited will flash.

Status & Monitoring

parameters in Menu 1 are read only and cannot be edited.

Once the change has been made, exit to

Parameter Select

by pressing the

Settings

button

or exit to

Status

by holding the

Settings

button

All parameters changes are saved immediately after exiting

Parameter Edit

5.6 Saving parameters

Parameter changes are saved automatically after editing by pressing or holding the

Settings

button

to return to

Parameter Select

Status

respectively. To save parameter changes over communications,

Save Parameters

(P4.19) should be set to 1. After saving the parameter will reset

to 0.

Содержание COMMANDER S100























































































































Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды

Nidec COMMANDER S100, Руководство пользователя

Результаты поиска

Содержание COMMANDER S100

Отзывы:

Похожие инструкции для COMMANDER S100

Бренды по названию

Популярные бренды