Nidec COMMANDER S100 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 118

background image

Drive parameters Communications

Diagnostics

106

Commander S100 User Guide

E029

An In 2 Current

A current loss was detected in T4 analog input 2 and the input type is set to 4-20 mA Error (6). Loss of input is detected if
the current falls below 3 mA.

Recommended actions:

•

Check control wiring is correct

•

Check control wiring is undamaged

•

Check T4

Analog Input 2 Type

(P6.02)

•

Check the current signal is present and greater than 3 mA

E030

Watchdog Timeout

Once the control word has been enabled, it must continue to be written to at least once a second to prevent a Watchdog
Timeout error from being generated.

E032

Supply Phase

The drive has detected a supply phase loss or large supply imbalance.

Recommended actions:

•

Check the A.C. supply voltage balance and level at full load

•

Check the output current stability

•

Reduce the duty cycle

•

Reduce the motor load

E033

Motor Resistance

The auto-tune test to measure the motor stator resistance has failed because the output current failed to rise to the correct
level to produce an accurate measurement.

Recommended actions:

•

Check the motor cable / connections

•

Check the integrity of the motor stator windings using an insulation tester

•

Check the motor phase to phase resistance at the drive terminals

•

Check the motor phase to phase resistance at the motor terminals

•

Select fixed boost mode in

Motor Control Mode

(P3.05) and verify the output current waveforms with an oscilloscope

•

Replace the motor

E034

Remote Keypad

A remote keypad has been removed whilst the RUN and STOP buttons have been configured to Run/Stop the drive.

Recommended Actions:

•

Check cable connection

E035

Control Word

Bit 12 (Control Word Error) in

Binary

Control Word

(P4.18) has been set to 1 whilst the control word is enabled (bit 15 = 1).

E036

User Save

The user-save parameters have been corrupted.

Recommended actions:

•

Restore Factory Defaults (P4.01)

E037

Power Down Save

The power down save parameters have been corrupted.

Recommended actions:

•

Restore Factory Defaults (P4.01)

E093

Inter-Processor

Communication between the control board processor and the power stage processor has been lost. This can be caused by
extreme levels of noise on the system, follow guidance in section 4.7

Electromagnetic compatibility (EMC)

.

E098

Motor Phase

Motor Output Phase Loss Detection

(P4.15) is enabled and a motor phase loss has been detected.

Recommended actions:

•

Check motor and drive connections

•

Check cable integrity

E099

Save Blocked

A save has been triggered while Marshal is attempting to communicate with the drive.

Recommended actions:

•

Save parameter settings using

Save Parameters

(P4.19)

Error

Diagnosis

«
...
104
105
106
107
108
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

VLT Integrated Servo Drive ISD 510 System

Бренд: Danfoss Страницы: 226

Бренд: HIKVISION Страницы: 9

PRO225LM Series

Бренд: Aerotech Страницы: 54

Бренд: Duratech Страницы: 39

Бренд: NI Страницы: 42

PARAMAX M Series

Бренд: Sumitomo Drive Technologies Страницы: 24

Native BACnet VLT HVAC Drive

Бренд: Danfoss Страницы: 31

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 2

Бренд: Graco Страницы: 4

Бренд: Lenovo Страницы: 68

DYER VCD 204-K-TMS+ Set

Бренд: D+H Страницы: 7

Sirio Entry 230

Бренд: Italtecnica Страницы: 116

Бренд: KB Electronics Страницы: 20

Бренд: Applied Biosystems Страницы: 124

RangeMaster V Series

Бренд: HardWay Страницы: 8

Бренд: STEP Страницы: 75

Бренд: Melec Страницы: 39

BTL5-H1 M Series

Бренд: Balluff Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды