Nidec COMMANDER S100 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 118

background image

Getting started

Commander S100 User Guide

69

P2.05

S-Ramp Percentage

Range:

0.00 to 50.0 %

Default:

0.0

An S-ramp allows for a smooth change in acceleration. To enable S-ramps, set this parameter to specify the percentage of the ramp time to include
an S-ramp profile.
If the S-ramp has been enabled and

Stopping Mode Selector

(P2.04) = Distance (5), the distance stop function will be disabled and the drive will

ramp to stop with the S-ramp enabled
It should be noted that as this parameter is increased, the time to ramp to maximum frequency does not change, instead the maximum acceleration
rate in the centre of the profile increases which causes a steeper linear portion at the centre of the profile.

Figure 7-4 S-Ramp set-up

P2.06

Acceleration Rate 1

Range:

0.1 to 1999.9 s

Default:

5.0

Defines the acceleration time from 0 Hz to the

Maximum Frequency Limit

(P2.02). An acceleration rate applies when the frequency is changing

away from 0 Hz.

P2.07

Deceleration Rate 1

Range:

0.1 to 1999.9 s

Default:

10.0

Defines the deceleration time from the maximum frequency limit to 0 Hz. A deceleration rate applies when the frequency is changing towards 0 Hz.

The drive may increase the ramp time due to the D.C. bus voltage controller, see

Deceleration Ramp Type

(P2.11).

P2.08

Acceleration Rate 2

Range:

0.1 to 1999.9 s

Default:

5.0

See

Acceleration Rate 1

(P2.06).

P2.09

Deceleration Rate 2

Range:

0.1 to 1999.9 s

Default:

10.0

See

Deceleration Rate 1

(P2.07).

P2.10

Ramp Rate Selector

Range:

0 to 2

Default:

0

Selects between ramp rates 1 or 2.

T

Ramp

T

S

Frequency (Hz)

S-Ramp set-up

T

S

= T

Ramp

x S Ramp Percentage (P2.05) / 100

Maximum
Frequency
P2.02

0

T

S

Time (s)

Value Description

0

The digital input function

Ramp Select

(12) is used to select between acceleration / deceleration rates 1 and 2, for more information

see Menu 6

IO Configuration

. This function can be selected for any of the digital inputs. If the digital input is inactive or if the function

has not been configured,

Acceleration Rate 1

(P2.06) and

Deceleration Rate 1

(P2.07) are used by the ramp system.

1

Acceleration Rate 1

(P2.06) and

Deceleration Rate 1

(P2.07) are used by the ramp system.

2

Acceleration Rate 2

(P2.08) and

Deceleration Rate 2

(P2.09) are used by the ramp system.

«
...
67
68
69
70
71
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

CLSM-150-B A Series

Бренд: Ewellix Страницы: 30

Бренд: Plextor Страницы: 82

Бренд: YASKAWA Страницы: 1016

Бренд: Fastech Страницы: 26

Бренд: Fröling Страницы: 44

Бренд: Omron Страницы: 48

Бренд: MKS Страницы: 5

Бренд: MAIMAN ELECTRONICS Страницы: 27

Бренд: Fujitsu Страницы: 138

Бренд: Fujitsu Страницы: 2

Advanced Line SP+ 075 ATEX MC

Бренд: Wittenstein Alpha Страницы: 52

Бренд: Novus Страницы: 71

Бренд: Shihlin Страницы: 220

Бренд: Shihlin electric Страницы: 242

Бренд: Coolmay Страницы: 99

SS Swerve (BLDC)

Бренд: WCP Страницы: 39

Бренд: HSB Страницы: 28

Бренд: Sanyo Denki Страницы: 266

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды