Nidec COMMANDER S100 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 118

background image

Getting started

60

Commander S100 User Guide

7.3 Parameter descriptions

This section provides detailed descriptions on the functions of all parameters within the drive.

7.3.1 Menu 1 - Status & monitoring (Read only)

This menu contains all parameters that show an output variable of the drive for status and monitoring purposes. All parameters in this menu are read-
only.
The majority of parameters are numbers that can be easily interpreted on the drive display. For indicator parameters, such as

Alarm Indicators

(P1.09), the drive displays an active bit with the 7-segment LEDs as shown in Figure 7-1 where bit 3 is active (1).

Figure 7-1 Binary parameter display

Bit

1

2

3

4

5

6

7

0

P1.01

Output Frequency

Range:

±

Maximum Frequency Limit

(P2.02) Hz

Default:

Read Only

Displays the drive output frequency in Hz. This is the sum of the

Ramp

 

Output

 

(P1.14) and motor slip compensation. A positive value is used for

forward rotation, a negative value is used for reverse rotation.

The range stated above applies for when the Output Frequency is used as an input or output such as when represented on T6 Analog Output. The
parameter may extend outside of this range if slip compensation hasn't been disabled or if the motor is being driven by another part of the machine
faster than the maximum frequency limit.

P1.02

Output Voltage

Range:

0 to Maximum Supply Voltage V (100 V & 200 V Drive = 240 V, 400 V Drive = 480 V)

Default:

Read Only

Displays

 

the

 

r.m.s. line to line voltage at the output terminals of the drive. (U to V; V to W; W to U.)

The range stated above applies for when the Output Voltage is used as an input or output such as when represented on T6 Analog Output. The
parameter may extend outside of this range if the drive is decelerating with high motor voltage enabled.

P1.03

Output Power

Range: 0 to Drive Rated Power x 2.2 kW

Default:

Read Only

Displays

 

the power flowing

 

through the output terminals of the drive. This parameter should be used for indication purposes only. A positive value

indicates power flowing from the drive to the motor.

P1.04

Motor RPM

Range: ±

18000 rpm

Default:

Read Only

Displays the motor RPM. The

Ramp Output

(P1.14) is converted to the equivalent RPM using the number of motor poles. The actual motor RPM

could be lower if

Motor Rated Speed

(P3.02) is not set correctly.

P1.05

Drive State

Range:

0 to 17

Default:

Read Only

Displays the present state of the drive as described below:

NOTE

NOTE

Value

Drive State

Description

0

Inhibited

The drive is not enabled

1

Ready

The drive is enabled but has not received a run signal

4

Running

The drive is running

5

Supply Loss

Supply loss has been detected

6

Deceleration

The drive is stopping the motor with a decelerating ramp

7

Injecting D.C

The drive is injecting D.C. braking current into the motor

9

Error

The drive in an error state, check the error log for more information

15

Under Voltage

The drive is in the under-voltage state

17

Initialising

The drive systems are initialising

«
...
58
59
60
61
62
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

Бренд: GEZE Страницы: 64

Бренд: Lenze Страницы: 210

Бренд: Teac Страницы: 1

Бренд: Chziri Страницы: 219

Бренд: Baldor Страницы: 48

iPOS80x0 BX-CAN

Бренд: Technosoft Страницы: 41

iPOS3602 HX-CAN

Бренд: Technosoft Страницы: 41

Бренд: Technosoft Страницы: 54

TOPVERT E1 Series

Бренд: TOPTEK Страницы: 78

Redi-Flo Series

Бренд: Grundfos Страницы: 16

Бренд: ZIEHL-ABEGG Страницы: 200

Бренд: ZIEHL-ABEGG Страницы: 204

Бренд: Acoms Страницы: 4

Бренд: Eurotherm Страницы: 221

Бренд: Zener Страницы: 2

VLT PROFINET MCA 120

Бренд: Danfoss Страницы: 76

Бренд: MAIMAN ELECTRONICS Страницы: 22

Бренд: Parker Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды