Nidec COMMANDER S100 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 118

background image

Getting started

Commander S100 User Guide

83

P4.17

Drive Enable

Range:

0 to 1

Default:

1 (On)

This must be set to On (1) to enable the drive unless

Binary Control Word

(P4.18) is enabled.

Figure 7-13 Drive Enable

P4.18

Binary Control Word

Range:

0 to 65535 (Binary 16 bit)

Default:

0

If Bit 15 in this parameter is set to zero then the parameter has no effect, but if it is set to one it overrides all of the corresponding inputs to the
sequencer and other digital input functions shown in the table below. Once the control word has been enabled, it must continue to be written to at
least once a second to prevent a watchdog timeout from being generated (Error 30). Disabling the control word returns the drive to terminal control
and the parameter no longer needs to be refreshed to prevent the watchdog timeout.
This should only be used by serial comms.
If a hardware enable is configured this will also be needed to enable the drive.

P4.19

Save Parameters

Range:

0 to 1

Default:

0 (No Action)

This parameter is intended to be used after parameters have been set by serial communications. If this parameter is set to On (1) then a full save
will be initiated. When the save is complete the parameter will be automatically reset to Off (0).

This parameter is not required when editing a parameter through the keypad or Marshal because a save is performed when pressing the settings
button or after parameters have been written to the drive by Marshal.

P4.20

Near Field Communication (NFC)

Range:

0 to 2

Default:

2 (Read & Write)

This parameter can be used to prevent or restrict NFC control via Marshal

If a security PIN is set in

Security PIN

(P4.02) this will apply to Marshal and parameters will not be able to be changed unless the PIN is provided.

&

Menu 6 I/O
Configuration

P1.11

Drive Enable P4.17

Bit 15

Control Word P4.18

1

0

Bit 0

Bit 1

Bit 0

Hardware Enable

Software Enable

Final Enable

Bit

Function

Description

Bit 0

Software Enable

Set to 1 to enable the drive

Bit 1

Run Forward

Set to 1 to run forward

Bit 2

Jog Forward

Set to 1 to jog forward

Bit 3

Run Reverse

Set to 1 to run in the reverse direction

Bit 4

Reverse

Set to 1 to reverse the direction

Bit 5

Run

Set to 1 to run

Bit 6

Run Permit (Not Stop)

Set to 1 to enable latching which will be cleared when set to 0

Bit 7

Frequency Switch bit 0

Used to select which reference is used by the reference system

Bit 8

Frequency Switch bit 1

Used to select which reference is used by the reference system

Bit 9

Jog Reverse

Set to 1 to jog in the reverse direction

Bit 10

Ramp Rate Selector

Used to select which ramp rates are used by the ramp system

Bit 11

Reserved

Not used by the drive

Bit 12

Initiate Error

Set to 1 to repeatedly initiate the Control Word error (E035)

Bit 13

Reset Drive

Set to 1 to reset the drive, clearing errors. This is automatically cleared

Bit 14

Reserved

Not used by the drive

Bit 15

Enable Control Word

Set to 1 to enable the binary control word

Value

NFC Allowed Actions

Description

0

Disabled

NFC communications are blocked

1

Read Only

The drive's NFC can be read offline by the app, and while on, drive configuration files and parameters
can be read

2

Read & Write

The drive's NFC features are fully enabled

NOTE

«
...
81
82
83
84
85
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

Бренд: Camozzi Страницы: 12

Бренд: Yuhai Страницы: 168

Бренд: Hitachi Страницы: 13

Бренд: Hitachi Страницы: 15

Бренд: Hitachi Страницы: 15

Бренд: Hitachi Страницы: 57

ThinkPad 43N3201

Бренд: Lenovo Страницы: 46

ThinkPad 40Y8626

Бренд: Lenovo Страницы: 58

ThinkCentre 41N5624

Бренд: Lenovo Страницы: 66

ThinkCentre 41N5626

Бренд: Lenovo Страницы: 72

ThinkPad 41N5643

Бренд: Lenovo Страницы: 46

ThinkPad 40Y8706

Бренд: Lenovo Страницы: 62

ThinkPad 40Y8710

Бренд: Lenovo Страницы: 68

Бренд: Lenovo Страницы: 70

Бренд: Lenovo Страницы: 6

Бренд: AMX Страницы: 2

Бренд: STG-BEIKIRCH Страницы: 25

Бренд: GEIGER Engineering Страницы: 147

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды