manualshive.com logo in svg

NetApp FAS2600, Руководство пользователя

NetApp FAS2600 - мощный и надежный хранилище данных для бизнеса. Получите бесплатное руководство пользователя, чтобы узнать о всех возможностях этого продукта. Скачайте руководство с manualshive.com уже сегодня, чтобы начать использование NetApp FAS2600 в своей компании.

Поделиться
Скачать
background image

Step 4: Reboot the controller after FRU replacement

After you replace the FRU, you must reboot the controller module.

Step

1. To boot ONTAP from the LOADER prompt, enter 

bye

.

Step 5: Switch back aggregates in a two-node MetroCluster configuration

After you have completed the FRU replacement in a two-node MetroCluster configuration, you can perform the
MetroCluster switchback operation. This returns the configuration to its normal operating state, with the sync-
source storage virtual machines (SVMs) on the formerly impaired site now active and serving data from the
local disk pools.

This task only applies to two-node MetroCluster configurations.

Steps

1. Verify that all nodes are in the 

enabled

 state: 

metrocluster node show

cluster_B::>  metrocluster node show

DR                           Configuration  DR
Group Cluster Node           State          Mirroring Mode
----- ------- -------------- -------------- ---------
--------------------
1     cluster_A
              controller_A_1 configured     enabled   heal roots
completed
      cluster_B
              controller_B_1 configured     enabled   waiting for
switchback recovery
2 entries were displayed.

2. Verify that resynchronization is complete on all SVMs: 

metrocluster vserver show

3. Verify that any automatic LIF migrations being performed by the healing operations were completed

successfully: 

metrocluster check lif show

4. Perform the switchback by using the 

metrocluster switchback

 command from any node in the

surviving cluster.

5. Verify that the switchback operation has completed: 

metrocluster show

The switchback operation is still running when a cluster is in the 

waiting-for-switchback

 state:

586

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Grundig RBX 1-RF Service Manual preview
RBX 1-RF
Бренд: Grundig Страницы: 16
QFX BT-207 Instruction Manual preview
BT-207
Бренд: QFX Страницы: 7
Yamaha MusicCast 200 TSX-N237 Brochure preview
MusicCast 200 TSX-N237
Бренд: Yamaha Страницы: 44
Sharp CP-XL45H Operation Manual preview
CP-XL45H
Бренд: Sharp Страницы: 33
Sharp CP-XL3000U Operation Manual preview
CP-XL3000U
Бренд: Sharp Страницы: 32
Sharp CP-XL1500H Operation Manual preview
CP-XL1500H
Бренд: Sharp Страницы: 37
Sharp CP-XL3000H Operation Manual preview
CP-XL3000H
Бренд: Sharp Страницы: 41
Sharp CP-V300H Service Manual preview
CP-V300H
Бренд: Sharp Страницы: 36
Sharp CP-S10 Operation Manual preview
CP-S10
Бренд: Sharp Страницы: 31
Sharp CP-UH25H Operation Manual preview
CP-UH25H
Бренд: Sharp Страницы: 36
Sharp CP-XL55 Service Manual preview
CP-XL55
Бренд: Sharp Страницы: 56
Sharp CP-XLT300H Service Manual preview
CP-XLT300H
Бренд: Sharp Страницы: 60
Sharp CP-UH4H Operation Manual preview
CP-UH4H
Бренд: Sharp Страницы: 44
Sharp CP-MP2H Operation Manual preview
CP-MP2H
Бренд: Sharp Страницы: 36
Sharp CP-UH240 Operation Manual preview
CP-UH240
Бренд: Sharp Страницы: 40
Sharp CP-UH220H Operation Manual preview
CP-UH220H
Бренд: Sharp Страницы: 44
Sharp CP-MP150 Operation Manual preview
CP-MP150
Бренд: Sharp Страницы: 42
Sharp CP-MP131 Operation Manual preview
CP-MP131
Бренд: Sharp Страницы: 42

Бренды по названию

Популярные бренды

Загрузить еще бренды