manualshive.com logo in svg

NetApp FAS2600, Руководство пользователя

NetApp FAS2600 - мощный и надежный хранилище данных для бизнеса. Получите бесплатное руководство пользователя, чтобы узнать о всех возможностях этого продукта. Скачайте руководство с manualshive.com уже сегодня, чтобы начать использование NetApp FAS2600 в своей компании.

Поделиться
Скачать
background image

4. Perform the switchback by using the 

metrocluster switchback

 command from any node in the

surviving cluster.

5. Verify that the switchback operation has completed: 

metrocluster show

The switchback operation is still running when a cluster is in the 

waiting-for-switchback

 state:

cluster_B::> metrocluster show
Cluster              Configuration State    Mode
--------------------    -------------------     ---------
 Local: cluster_B configured        switchover
Remote: cluster_A configured        waiting-for-switchback

The switchback operation is complete when the clusters are in the 

normal

 state.:

cluster_B::> metrocluster show
Cluster              Configuration State    Mode
--------------------    -------------------     ---------
 Local: cluster_B configured            normal
Remote: cluster_A configured            normal

If a switchback is taking a long time to finish, you can check on the status of in-progress baselines by using
the 

metrocluster config-replication resync-status show

 command.

6. Reestablish any SnapMirror or SnapVault configurations.

Step 4: Return the failed part to NetApp

Return the failed part to NetApp, as described in the RMA instructions shipped with the kit. See the 

Part Return

& Replacements

 page for further information.

Controller module

Overview of controller module replacement - AFF A700 and FAS9000

You must review the prerequisites for the replacement procedure and select the correct
one for your version of the ONTAP operating system.

• All drive shelves must be working properly.

• If your system is a FlexArray system or has a V_StorageAttach license, you must refer to the additional

required steps before performing this procedure.

• If your system is in an HA pair, the healthy node must be able to take over the node that is being replaced

(referred to in this procedure as the “impaired node”).

• If your system is in a MetroCluster configuration, you must review the section 

Choosing the correct

recovery procedure

 to determine whether you should use this procedure.

If this is the procedure you should use, note that the controller replacement procedure for a node in a four
or eight node MetroCluster configuration is the same as that in an HA pair. No MetroCluster-specific steps

605

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Teac CD-X9 Owner'S Manual preview
CD-X9
Бренд: Teac Страницы: 24
TeachLogic Maxim III Installation Manual preview
Maxim III
Бренд: TeachLogic Страницы: 21
Panasonic SC-PM250 Operating Instructions preview
SC-PM250
Бренд: Panasonic Страницы: 2
Fender PA 135 Manual preview
PA 135
Бренд: Fender Страницы: 6
eMoMo Remo4 Quick Start Manual preview
Remo4
Бренд: eMoMo Страницы: 2
Goodmans MICRO1470DABI User Manual preview
MICRO1470DABI
Бренд: Goodmans Страницы: 22
Jensen JWM40 Quick Reference Manual preview
JWM40
Бренд: Jensen Страницы: 2
Teac CR-K1 Service Manual preview
CR-K1
Бренд: Teac Страницы: 16
Bogen NEARSCAPES 4.1 Manual preview
NEARSCAPES 4.1
Бренд: Bogen Страницы: 2
Panasonic SAAK630 - MINI HES W/CD PLAYER Operating Instructions Manual preview
SAAK630 - MINI HES W/CD PLAYER
Бренд: Panasonic Страницы: 16
Panasonic SAAK320 - MINI HES W/CD PLAYER Operating Instructions Manual preview
SAAK320 - MINI HES W/CD PLAYER
Бренд: Panasonic Страницы: 20
Panasonic SAAK600 - MINI HES W/CD PLAYER Operating Instructions Manual preview
SAAK600 - MINI HES W/CD PLAYER
Бренд: Panasonic Страницы: 32
Panasonic SAAK33 - MINI HES W/CD Service Manual preview
SAAK33 - MINI HES W/CD
Бренд: Panasonic Страницы: 26
Panasonic SAAK70 - MINI HES W/CD-P Operating Instructions Manual preview
SAAK70 - MINI HES W/CD-P
Бренд: Panasonic Страницы: 40
Panasonic SAAK58 - MINI HES W/CD Operating Instructions Manual preview
SAAK58 - MINI HES W/CD
Бренд: Panasonic Страницы: 40
Panasonic SAAK57 - MINI HES W/CD-P Operating Instructions Manual preview
SAAK57 - MINI HES W/CD-P
Бренд: Panasonic Страницы: 44
Panasonic SAAK300 - MINI HES W/CD PLAYER Service Manual preview
SAAK300 - MINI HES W/CD PLAYER
Бренд: Panasonic Страницы: 62
Panasonic SAAK27 - MINI HES W/CD-P Service Manual preview
SAAK27 - MINI HES W/CD-P
Бренд: Panasonic Страницы: 81

Бренды по названию

Популярные бренды

Загрузить еще бренды