NetApp FAS2600 Скачать руководство пользователя страница 413 | Manualshive

Страница: 413 / 786

background image

Step 2: Install the hardware

You need to install your system in a 4-post rack or NetApp system cabinet, as applicable.

Steps

1. Install the rail kits, as needed.

2. Install and secure your system using the instructions included with the rail kit.

You need to be aware of the safety concerns associated with the weight of the system.

3. Attach cable management devices (as shown).

4. Place the bezel on the front of the system.

Step 3: Cable controllers to your network

You can cable the controllers to your network by using the two-node switchless cluster
method or by using the cluster interconnect network.

Option 1: Cable a two-node switchless cluster

The optional data ports, optional NIC cards, and management ports on the controller
modules are connected to switches. The cluster interconnect and HA ports are cabled on
both controller modules.

You must have contacted your network administrator for information about connecting the system to the
switches.

Be sure to check the direction of the cable pull-tabs when inserting the cables in the ports. Cable pull-tabs are
up for all onboard ports and down for expansion (NIC) cards.

411

«
...
411
412
413
414
415
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: auna multimedia Страницы: 30

Бренд: Audiocenter Страницы: 40

Бренд: The Fisher Страницы: 20

Бренд: iDance Страницы: 16

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 40

Бренд: Kenwood Страницы: 64

Бренд: Kenwood Страницы: 64

Бренд: Kenwood Страницы: 64

Бренд: Kenwood Страницы: 68

Бренд: Kenwood Страницы: 72

Бренд: Kenwood Страницы: 76

Бренд: Kenwood Страницы: 77

Бренд: Marley Страницы: 64

Бренд: LENCO Страницы: 10

Бренд: Dell EMC Страницы: 71

Бренд: Paradigm Страницы: 22

Бренд: B2 Audio Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды