NetApp FAS2600 Скачать руководство пользователя страница 737 | Manualshive

Страница: 737 / 786

background image

If your system is running ONTAP…

Then…

With more than two nodes in the cluster

Issue this command:

node::> storage failover

modify -node node0 -enabled true

In a stand-alone configuration

You have no further steps in this particular task.
You have completed system-level diagnostics.

Resulted in some test failures

Determine the cause of the problem.

a. Exit Maintenance mode:

halt

b. Perform a clean shutdown, and then disconnect

the power supplies.

c. Verify that you have observed all of the

considerations identified for running system-level
diagnostics, that cables are securely connected,
and that hardware components are properly
installed in the storage system.

d. Reconnect the power supplies, and then power on

the storage system.

e. Rerun the system-level diagnostics test.

Step 3: Return the failed part to NetApp

Return the failed part to NetApp, as described in the RMA instructions shipped with the kit. See the

page for further information.

Controller module

Replace the controller module - FAS9500

To replace the impaired controller module, you must shut down the impaired controller,
move the internal components to the replacement controller module, install the
replacement controller module, and reboot the replacement controller.

Before you begin

You must review the prerequisites for the replacement procedure and select the correct one for your version of
the ONTAP operating system.

• All drive shelves must be working properly.

• If your system is a FlexArray system or has a V_StorageAttach license, you must refer to the additional

required steps before performing this procedure.

• If your system is in an HA pair, the healthy node must be able to take over the node that is being replaced

(referred to in this procedure as the “impaired node”).

• If your system is in a MetroCluster configuration, you must review the section

Choosing the correct

recovery procedure

to determine whether you should use this procedure.

If this is the procedure you should use, note that the controller replacement procedure for a node in a four

735

«
...
735
736
737
738
739
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: E-Mu Страницы: 72

Бренд: E-Mu Страницы: 44

Бренд: Garmin Страницы: 10

ETR 2000 series

Бренд: Delco Страницы: 34

Бренд: Krüger & Matz Страницы: 58

Бренд: Aiwa Страницы: 32

Бренд: Aiwa Страницы: 32

Бренд: Aiwa Страницы: 36

Бренд: Blue Smoke Страницы: 31

Бренд: LENCO Страницы: 92

Бренд: easyRAID Страницы: 32

Бренд: Eagle Страницы: 101

Бренд: Noam Страницы: 8

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 10

Бренд: RCA Страницы: 17

Бренд: RCA Страницы: 18

Бренд: RCA Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды