NetApp FAS2600 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 786

background image

13. Return the failed part to NetApp, as described in the RMA instructions shipped with the kit.

Contact technical support at

, 888-463-8277 (North America), 00-800-44-638277

(Europe), or +800-800-80-800 (Asia/Pacific) if you need the RMA number or additional help with the
replacement procedure.

Replace the NVMEM battery - FAS2600

To replace an NVMEM battery in the system, you must remove the controller module from
the system, open it, replace the battery, and close and replace the controller module.

All other components in the system must be functioning properly; if not, you must contact technical support.

AFF FAS2600 NVMEM battery replacement video

Step 1: Shut down the impaired controller

You can shut down or take over the impaired controller using different procedures, depending on the storage
system hardware configuration.

To shut down the impaired controller, you must determine the status of the controller and, if necessary, take
over the controller so that the healthy controller continues to serve data from the impaired controller storage.

If you have a cluster with more than two nodes, it must be in quorum. If the cluster is not in quorum or a healthy
controller shows false for eligibility and health, you must correct the issue before shutting down the impaired
controller; see the

Administration overview with the CLI

.

Steps

1. If AutoSupport is enabled, suppress automatic case creation by invoking an AutoSupport message:

system node autosupport invoke -node * -type all -message
MAINT=_number_of_hours_down_h

The following AutoSupport message suppresses automatic case creation for two hours:

cluster1:*>

system node autosupport invoke -node * -type all -message MAINT=2h

2. If the impaired controller is part of an HA pair, disable automatic giveback from the console of the healthy

controller:

storage failover modify -node local -auto-giveback false

3. Take the impaired controller to the LOADER prompt:

If the impaired controller is
displaying…

Then…

The LOADER prompt

Go to Remove controller module..

Waiting for giveback…

Press Ctrl-C, and then respond

y

.

159

«
...
159
160
161
162
163
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: Sound Freaq Страницы: 19

Бренд: Lightspeed Страницы: 42

Бренд: Lightspeed Страницы: 88

Бренд: Curtis Страницы: 1

Бренд: Curtis Страницы: 1

Бренд: Curtis Страницы: 1

Бренд: audisse Страницы: 137

Бренд: Bush Страницы: 18

Бренд: Bush Страницы: 27

Бренд: Daewoo Страницы: 29

Бренд: NCE Страницы: 16

Theatre Box CBT612

Бренд: Acemile Страницы: 4

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 28

Бренд: Sanyo Страницы: 34

Бренд: Sanyo Страницы: 52

Бренд: Sanyo Страницы: 38

Бренд: Sanyo Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды