NetApp FAS2600 Скачать руководство пользователя страница 491 | Manualshive

Страница: 491 / 786

background image

on the air duct for more information.

• If you have a FAS8300 system, the system DIMMs are located in sockets 2, 4, 13, and 15.

• If you have a FAS8700 system, the system DIMMs are located in slots 2, 4, 7, 9, 13, 15, 18, and 20.

• The NVDIMM is located in slot 11.

Steps

1. Open the air duct:

a. Press the locking tabs on the sides of the air duct in toward the middle of the controller module.

b. Slide the air duct toward the back of the controller module, and then rotate it upward to its completely

open position.

2. Locate the DIMMs on your controller module.

3. Note the orientation of the DIMM in the socket so that you can insert the replacement DIMM in the proper

orientation.

4. Eject the DIMM from its socket by slowly pushing apart the two DIMM ejector tabs on either side of the

DIMM, and then slide the DIMM out of the socket.

Carefully hold the DIMM by the edges to avoid pressure on the components on the DIMM
circuit board.

5. Remove the replacement DIMM from the antistatic shipping bag, hold the DIMM by the corners, and align it

to the slot.

The notch among the pins on the DIMM should line up with the tab in the socket.

6. Make sure that the DIMM ejector tabs on the connector are in the open position, and then insert the DIMM

squarely into the slot.

The DIMM fits tightly in the slot, but should go in easily. If not, realign the DIMM with the slot and reinsert it.

Visually inspect the DIMM to verify that it is evenly aligned and fully inserted into the slot.

7. Push carefully, but firmly, on the top edge of the DIMM until the ejector tabs snap into place over the

notches at the ends of the DIMM.

8. Close the air duct.

Step 4: Install the controller module

After you have replaced the component in the controller module, you must reinstall the
controller module into the chassis, and then boot it to Maintenance mode.

You can use the following animation, drawing, or the written steps to install the controller module in the
chassis.

Installing the controller module

489

«
...
489
490
491
492
493
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: ALLEN & HEATH Страницы: 14

Бренд: dB Technologies Страницы: 2

Бренд: Suzuki Страницы: 150

Бренд: LG Страницы: 24

Бренд: LG Страницы: 23

Бренд: LG Страницы: 12

Бренд: LG Страницы: 26

FA64 (FA64-D0U/ FAS64F)

Бренд: LG Страницы: 12

Бренд: LG Страницы: 19

Бренд: LG Страницы: 36

Бренд: LG Страницы: 24

Бренд: LG Страницы: 28

Бренд: LG Страницы: 51

Бренд: LG Страницы: 12

Бренд: LG Страницы: 32

Бренд: LG Страницы: 40

Бренд: LG Страницы: 4

Бренд: LG Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды