NetApp FAS2600 Скачать руководство пользователя страница 314

Страница: 314 / 786

Check the output of the security key-manager query again to ensure that the

Restored

column =

yes

and all key managers report in an available state

11. If the Onboard Key Management is enabled:

a. Use the

security key-manager key show -detail

to see a detailed view of all keys stored in

the onboard key manager.

b. Use the

security key-manager key show -detail

command and verify that the

Restored

column =

yes

for all authentication keys.

If the

Restored

column = anything other than

yes

, use the

security key-manager setup

-node

Repaired

(Target)

node

command to restore the Onboard Key Management settings.

Rerun the

security key-manager key show -detail

command to verify

Restored

column =

yes

for all authentication keys.

12. Connect the console cable to the partner controller.

13. Give back the controller using the

storage failover giveback -fromnode local

command.

14. Restore automatic giveback if you disabled it by using the

storage failover modify -node local

-auto-giveback true

command.

Option 3: Restore NSE/NVE on systems running ONTAP 9.6 and later

Steps

1. Connect the console cable to the target controller.

2. Use the

boot_ontap

command at the LOADER prompt to boot the controller.

3. Check the console output:

If the console
displays…

Then…

The login prompt

Go to Step 7.

Waiting for giveback…

a. Log into the partner controller.

b. Confirm the target controller is ready for giveback with the

storage

failover show

command.

4. Move the console cable to the partner controller and give back the target controller storage using the

storage failover giveback -fromnode local -only-cfo-aggregates true local

command.

◦

If the command fails because of a failed disk, physically disengage the failed disk, but leave the disk in
the slot until a replacement is received.

◦

If the command fails because of an open CIFS session, check with the customer on how to close out
CIFS sessions.

Terminating CIFS can cause loss of data.

◦

If the command fails because the partner is "not ready", wait 5 minutes for the NVMEMs to
synchronize.

312

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FAS2600

Отзывы:

Похожие инструкции для FAS2600

Бренды по названию

Популярные бренды

NetApp FAS2600, Руководство пользователя

Результаты поиска

Содержание FAS2600

Отзывы:

Похожие инструкции для FAS2600

Бренды по названию

Популярные бренды