NetApp FAS2600 Скачать руководство пользователя страница 692 | Manualshive

Страница: 692 / 786

background image

Be sure to check the direction of the cable pull-tabs when inserting the cables in the ports. Cable pull-tabs
are up for all networking module ports.

As you insert the connector, you should feel it click into place; if you do not feel it click,
remove it, turn it over and try again.

1. Use the animation or illustration to complete the cabling between the controllers and to the switches:

<div class="aspect-ratio"><iframe frameborder="1" height="400"
scrolling="auto"
src="https://netapp.hosted.panopto.com/Panopto/Pages/embed.aspx?id=3
ad3f118-8339-4683-865f-ae7c0170400c" width="711"> </iframe></div>

Animation - Switched cluster cabling

690

«
...
690
691
692
693
694
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: Onn Страницы: 11

MM2040 TOUCHBOX

Бренд: Manta Страницы: 16

SA10201 - Boom Box Audio System

Бренд: Delphi Страницы: 12

Бренд: Ferguson Страницы: 13

L.O.C.PRO LPGL-2

Бренд: PAC Страницы: 2

Бренд: Sharp Страницы: 20

Бренд: LG Страницы: 20

Бренд: LG Страницы: 24

Бренд: LG Страницы: 47

Бренд: LG Страницы: 8

Бренд: LG Страницы: 18

Бренд: LG Страницы: 22

Бренд: LG Страницы: 18

Бренд: LG Страницы: 10

Бренд: LG Страницы: 16

Бренд: LG Страницы: 104

Бренд: LG Страницы: 42

Бренд: LG Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды