NetApp FAS2600 Скачать руководство пользователя страница 208

Страница: 208 / 786

• If NSE or NVE are enabled for ONATP 9.5, go to

Option 2: Restore NSE/NVE on systems running ONTAP

9.5 and earlier

• If NSE or NVE are enabled for ONTAP 9.6, go to

Option 3: Restore NSE/NVE on systems running ONTAP

9.6 and later

Option 1: Restore NVE or NSE when Onboard Key Manager is enabled

Steps

1. Connect the console cable to the target controller.

2. Use the

boot_ontap

command at the LOADER prompt to boot the controller.

3. Check the console output:

If the console
displays…

Then…

The LOADER prompt

Boot the controller to the boot menu:

boot_ontap menu

Waiting for giveback…

a. Enter

Ctrl-C

at the prompt

b. At the message: Do you wish to halt this controller rather than wait [y/n]? ,

enter:

c. At the LOADER prompt, enter the

boot_ontap menu

command.

4. At the Boot Menu, enter the hidden command,

recover_onboard_keymanager

and reply

at the

prompt.

5. Enter the passphrase for the onboard key manager you obtained from the customer at the beginning of this

procedure.

6. When prompted to enter the backup data, paste the backup data you captured at the beginning of this

procedure, when asked. Paste the output of

security key-manager backup show

security

key-manager onboard show-backup

command.

The data is output from either

security key-manager backup show

security

key-manager onboard show-backup

command.

Example of backup data:

206

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FAS2600

Отзывы:

Похожие инструкции для FAS2600

Бренды по названию

Популярные бренды

NetApp FAS2600, Руководство пользователя

Результаты поиска

Содержание FAS2600

Отзывы:

Похожие инструкции для FAS2600

Бренды по названию

Популярные бренды