NetApp FAS2600 Скачать руководство пользователя страница 775 | Manualshive

Страница: 775 / 786

background image

HA

state:

ha-config show

If your system is in…

The HA state for all components should be…

An HA pair

ha

A MetroCluster FC configuration
with four or more nodes

mcc

A MetroCluster IP configuration

mccip

2. If the displayed system state of the controller module does not match your system configuration, set the

HA

state for the controller module:

ha-config modify controller

ha-state

3. If the displayed system state of the chassis does not match your system configuration, set the

HA

state for

the chassis:

ha-config modify chassis

ha-state

Step 6: Reassigning disks

You must confirm the system ID change when you boot the replacement node and then verify that the change
was implemented.

This procedure applies only to systems running ONTAP in an HA pair.

Steps

1. If the replacement node is in Maintenance mode (showing the

*>

prompt), exit Maintenance mode and go

to the LOADER prompt:

halt

2. From the LOADER prompt on the replacement node, boot the node, entering

y

if you are prompted to

override the system ID due to a system ID mismatch.

3. Wait until the

Waiting for giveback…

message is displayed on the replacement node console and

then, from the healthy node, verify that the new partner system ID has been automatically assigned:

storage failover show

In the command output, you should see a message that the system ID has changed on the impaired node,
showing the correct old and new IDs. In the following example, node2 has undergone replacement and has
a new system ID of 151759706.

node1> `storage failover show`
Takeover
Node Partner Possible State Description
------------ ------------ --------
-------------------------------------
node1 node2 false System ID changed on
partner (Old:
151759755, New:
151759706), In takeover
node2 node1 - Waiting for giveback
(HA mailboxes)

773

«
...
773
774
775
776
777
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: Jensen Страницы: 12

Бренд: Subpac Страницы: 15

Бренд: Hama Страницы: 76

SAPM38 - CD STEREO SYSTEM

Бренд: Panasonic Страницы: 48

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 25

Бренд: Nagra Страницы: 22

Бренд: RCA Страницы: 27

Бренд: DAEWOO ELECTRONICS Страницы: 35

Бренд: REDCAT Страницы: 76

Бренд: easyRAID Страницы: 19

Бренд: easyRAID Страницы: 38

DSN-2100-10 - xStack Storage Area Network Array Hard...

Бренд: D-Link Страницы: 36

Бренд: Yamaha Страницы: 26

Бренд: Panasonic Страницы: 78

Бренд: Curtis Страницы: 9

Бренд: Philips Страницы: 31

Бренд: Philips Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды