NetApp FAS2600 Скачать руководство пользователя страница 715 | Manualshive

Страница: 715 / 786

background image

a. Check the boot environment variables:

▪

bootarg.init.boot_clustered

▪

partner-sysid

▪

bootarg.init.flash_optimized for AFF

▪

bootarg.init.san_optimized for AFF

▪

bootarg.init.switchless_cluster.enable

b. If External Key Manager is enabled, check the bootarg values, listed in the

kenv

ASUP output:

▪

bootarg.storageencryption.support <value>

▪

bootarg.keymanager.support <value>

▪

kmip.init.interface <value>

▪

kmip.init.ipaddr <value>

▪

kmip.init.netmask <value>

▪

kmip.init.gateway <value>

c. If Onboard Key Manager is enabled, check the bootarg values, listed in the

kenv

ASUP output:

▪

bootarg.storageencryption.support <value>

▪

bootarg.keymanager.support <value>

▪

bootarg.onboard_keymanager <value>

d. Save the environment variables you changed with the

savenv

command

e. Confirm your changes using the

printenv variable-name

command.

7. Set your network connection type at the LOADER prompt:

◦

If you are configuring DHCP:

ifconfig e0a -auto

The target port you configure is the target port you use to communicate with the
impaired node from the healthy node during var file system restore with a network
connection. You can also use the e0M port in this command.

◦

If you are configuring manual connections:

ifconfig e0a -addr=filer_addr -mask=netmask

-gw=gateway-dns=dns_addr-domain=dns_domain

▪

filer_addr is the IP address of the storage system.

▪

netmask is the network mask of the management network that is connected to the HA partner.

▪

gateway is the gateway for the network.

▪

dns_addr is the IP address of a name server on your network.

▪

dns_domain is the Domain Name System (DNS) domain name.

If you use this optional parameter, you do not need a fully qualified domain name in the netboot
server URL. You need only the server’s host name.

Other parameters might be necessary for your interface. You can enter help ifconfig at the
firmware prompt for details.

713

«
...
713
714
715
716
717
...
»

Содержание FAS2600



















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAS2600

Бренд: Hama Страницы: 75

Бренд: Aiwa Страницы: 20

Бренд: Bluestream Страницы: 4

Бренд: S.E.M. Страницы: 6

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 16

Бренд: Sharp Страницы: 116

Бренд: Silvercrest Страницы: 24

Бренд: Silvercrest Страницы: 35

Бренд: Silvercrest Страницы: 42

Бренд: Silvercrest Страницы: 58

Бренд: Silvercrest Страницы: 62

Бренд: Roadstar Страницы: 11

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 19

Бренд: Philips Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды